background image

A

B

C

A) End of shaft with nut

B) Washer

C) Elbow (if needed)
Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue with

the gas connection.
The flexible pipe is prepared for apply when:
• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting edges or

corners;

• it can be easily examined in order to make

sure its condition.

The control of preservation of the flexible pipe

consists in checking that:
• it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

• the material is not hardened, but shows its

correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not repair

the pipe, but replace it.

WARNING!

When installation is complete, make

sure that the seal of each pipe fitting

is correct. Use a soapy solution, not

a flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the

injectors and replace them with the ones

which are necessary for the type of gas you

use (see table in "Technical Information"

chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must

fit an applicable pressure adjuster on the gas

supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:
1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).

A

5. If you change:

• from natural gas G20 20 mbar to liquid

gas, fully tighten the bypass screw in.

• from liquid gas to natural gas G20 20

mbar, undo the bypass screw

approximately 1/4 of a turn.

WARNING!

Make sure the flame does not go out

when you quickly turn the knob from

the maximum position to the

minimum position.

Electrical connection

• Make sure that the rated voltage and type of

power on the rating plate agree with the

voltage and the power of the local power

supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a correct

plug which can hold the load that the rating

plate rates. Make sure that you install the

plug in a correct socket.

• Always use a correctly installed shockproof

socket.

• Make sure that there is an access to the

mains plug after the installation.

www.zanussi.com

11

Summary of Contents for ZGO63414













































Reviews: