background image

3

1.Instruction for the User

HOB BURNERS CONTROL KNOBS

The hob burners control knobs are situated on the hob
front panel. The symbols on the knobs mean that :

 

 

there is no gas supply

 

there is maximum gas supply

  

there is minimum gas supply

LIGHTING THE BURNERS

• For easier lighting, proceed before putting a pan

on the pan support.

Push the relevant knob down and turn it anti-
clockwise until it reaches the "maximum" position.
After lighting the flame, keep the knob pushed down

for about 5 seconds. This will allow the

"thermocouple" (Fig. 1 lett. D) to be heated and the

safety device to be switched off, otherwise the gas
supply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) and the
"crown" (Fig. 1 lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol 

.

• Always turn the flame down or put it out before

taking the pans off the burner.

USING THE HOB CORRECTLY

To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
flat bottom fitting the size of the burner used, so that
flame will not spread beyond the bottom of the vessel
(see the table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.

Carefully supervise cookings with 

fats or oil

,

since these types of foodstuff can result in a fire,
if over-heated.

Burner

minimum

maximum

diameter

diameter

Big (rapid)

180 mm.

260 mm.

Medium (semirapid)

120 mm.

220 mm.

Small (Auxiliary)

80 mm.

160 mm.

Fig. 1

Contents

FO 0204

1. Instruction for the User ............

Pag.

3

2. Cleaning and Maintenance .......

Pag.

4

3.  Periodic Maintenance ................

Pag.

5

4.  Maintenance -

    Technical assistance ..................

Pag.

5

5. Technical Data ...........................

Pag.

6

6. Instruction for the Installer .......

Pag.

6

7. Electrical Connection................

Pag.

7

8. Adaptation to different

types of gas ...............................

Pag.

8

9. Building In ..................................

Pag.

9

Summary of Contents for ZGF 646 ICW













Reviews: