background image

25

MAINTENANCE

Idle periods

During periods when the appliance is not used, you 
should take the following precautions:

remove the plug from the wall socket;

remove all food from the appliance;

defrost and clean the interior and all accessories;

leave the door slightly open, thus letting air circulate 
and preventing the formation of mould and unpleasant 
smells.

Unplug the appliance before carrying out any 
maintenance operation.

Periodic cleaning

When defrosting, wash the interior of the appliance 
with lukewarm water and sodium bicarbonate.

SOMETHING NOT WORKING

If the appliance is not functioning properly check 
that:

the plug is firmly in the wall socket and the mains 
power switch is on;

there is no power failure;

the control knob is in the right position.

If your appliance is still not working properly after 
making the above checks, contact your local dealer or 
the nearest service centre.

To obtain fast service, it is essential that when you 
apply for it you specify the model and serial number 
of your appliance which can be found inside the 
appliance at the bottom on the left hand side.

GB

GB

Summary of Contents for ZF 134 UN














Reviews: