background image

Problem

Possible cause and solution

There are whitish streaks or blu-

ish layers on glasses and dishes.

• The release quantity of rinse aid is too much. Adjust the rinse

aid level to a lower level.

• The quantity of detergent is too much.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust the

rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The dishes are wet.

• For the best drying performance activate the option XtraDry.

• The programme does not have a drying phase or has a drying

phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a differ-

ent brand or activate the rinse aid dispenser and use rinse

aid and multi-tablets together.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the hu-

midity in the air that condenses on the walls.

Unusual foam during washing.

• Use the detergent for dishwashers only.

• There is a leak in the rinse aid dispenser. Contact an Author-

ised Service Centre.

Traces of rust on cutlery.

• There is too much salt in the water used for washing. Refer to 

"The water softener".

• Silver and stainless steel cutlery were placed together. Avoid

to put silver and stainless steel items close together.

There are residues of detergent

in the dispenser at the end of the

programme.

• The detergent tablet got stuck in the dispenser and therefore

was not completely washed away by water.

• Water cannot wash away the detergent from the dispenser.

Make sure that the spray arm is not blocked or clogged.

• Make sure that items in the baskets do not impede the lid of

the detergent dispenser from opening.

Odours inside the appliance.

• Refer to "Internal cleaning".

Limescale deposits on the table-

ware, on the tub and on the in-

side of the door.

• Refer to "The water softener".

Dull, discoloured or chipped ta-

bleware.

• Make sure that only dishwasher-safe items are washed in the

appliance.

• Load and unload the basket carefully. Refer to basket loading

leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use""Daily

use" or "Hints and tips" for other

possible causes.

17

Summary of Contents for ZDT26010FA





















Reviews: