Zanussi ZCGHL54 User Manual Download

Page: 28 / 36

Technical details

Dimensions

Height:

1462mm (nominal)

Width:

554mm

Depth:

600mm (from elbow to front of door panel)

Weight:

61 .8 Kg

Height to hotplate

907 mm nominal. See important note ‘Location of appliance’.

Space for fixing at hotplate level

2mm minimum clearance

600 nominal

Space for fixing above hotplate level 100mm each side of appliance.

Minimum space above grill

500mm

Minimum distance from rear of wall

20mm

Connections

Gas connection:-

Rear left hand side of appliance at hotplate level

Rc ½” (½” B.S.P. female)

Electrical connection:-

None

Ignition

Battery 1.5 Volt AA size

Hotplate

Natural Gas

Heat input

R.H.F

R.H.R

L.H.R

L.H.F.

1.0kW

1.9kW

2.9kW

(3412 Btu/h) (6483 Btu/h) (6483 Btu/h) (9895 Btu/h)

Injector marking

070

096

119

L.P. Gas

Heat input

1.0kW

1.9kW

2.8kW

(71.8g/h)

(136.5g/h)

(194.0g/h)

Injector marking

050

071

086

Summary of Contents for ZCGHL54





































Search results

Summary of Contents for ZCGHL54

Reviews:

Related manuals for ZCGHL54

Brands by name

Popular brands

Zanussi ZCGHL54, User Manual

Search results

Summary of Contents for ZCGHL54

Reviews:

Related manuals for ZCGHL54

Brands by name

Popular brands