background image

 

29

 

MAINTENANCE

 

Unplug the appliance before carrying out any 
maintenance operation.

 

Periodic cleaning

 

Clean the inside with warm water and bicarbonate 
of soda.
Clean the outside with a silicone wax spray.
Clean the condenser and compressor with a brush 
or vacuum cleaner. This will improve performance 
and consequently save on electricity.

 

Periods of non-use

 

If you are not using the appliance for any length of 
time, the following precautions should be taken:

unplug the appliance;

take all food out;

defrost and clean the inside and all the accessories;

leave the door ajar so that air can circulate inside in 
order to prevent unpleasant smells forming.

 

The light bulb

 

The opening on the diffuser gives access to the light 
bulb.
If the light does not come on when the door is 
opened, check that the bulb is screwed in properly; 
replace the bulb if the fault persists.
The rating is shown on the light bulb cover.

 

TROUBLESHOOTING

 

If a fault occurs, check:

– that the plug is correctly inserted in the socket;

– that the socket is powered;

– that the thermostat dial is correctly positioned.

 

Also check the following:

 

If the appliance is very noisy, check that the sides 
are not vibrating against adjacent kitchen units and 
that the refrigeration unit pipes are not vibrating.

If the fault persists after carrying out the above 
checks, call your nearest Servicing Centre.

 

For quick service it is important when telephoning to 
give the number of the model and the serial number, 
both of which can be found on the serial number plate 
inside at the bottom left of the appliance.

 

GB

GB

Summary of Contents for Z 140 T








Reviews: