Zanussi Electrolux Built-in oven User Manual Download Page 10

44

Terminal block

The oven has an easily accessible terminal block,

which is meant to work with an electric single-phase

rate of 230 V.

The  manufacturer  disclaims  any

responsability should all the safety

measures not be carried out.

Electrical Connection

Before the appliance is connected:
1) check that the main fuse and the domestic installation

can support the load;

2) check that the power supply is properly earthed in

compliance with the current rules;

3) check the socket or the double pole switch used for

the electrical connection can be easily reached with

the appliance built in the forniture unit.

This appliance is delivered without an electric supply

cable,  therefore,  you  will  have  to  fit  to  it  a  supply

cable with standard plug, suitable for the total electric

load  shown  on  the  rating  plate.  The  plug  is  to  be

inserted into a suitable wall socket.

If connecting the appliance directly to the electric system,

a  double  pole  switch  must  be  installed  between  the

appliance and the electricity supply, with a minimum

gap of 3 mm. between the switch contacts and of a type

suitable for the required load in compliance with the

current rules. The earth wire must not be interrupted by

the double switch pole.

The connection cable has to be placed in order that, in

each part, it cannot reach a temperature 50 °C higher

than the room temperature.

After  the  connection  is  carried  out,  test  the  heating

elements for about 3 minutes.

Suitable power supply cables are the following types,

considering the respective necessary section of cable.

H07 RN-F

H05 RN-F

H05 RR-F

H05 VV-F

FO 2159

Fig. 14

FO 0039

Fig. 13

Securing the Oven to the

Cabinet

Fit the appliance into the cabinet recess.

Open teh oven door and secure the oven to the kitchen

cabinet  with  four  wood  screws,  which  fit  the  holes

provided in the oven frame 

(Fig.13).

When installing an electric plate hob over the oven, the

hob's electrical connection and the oven's one have to

be carried out separately, for security reasons and to let

the oven be taken off the unit easier, if necessary.

Summary of Contents for Built-in oven















Reviews: