FUNCTIONING, MOUNTING RNK-04
By pressing the button, the transmitter sends a signal with 868,32 MHz frequency
which controls EXTA FREE receivers.
Device programming procedure (adding a
transmitter to a receiver’s memory) is described in particular EXTA FREE man-
ual instructions.
The device range (up to 250 m depending on a receiver) can be
increased by means of a retransmitter or few RTN-01 retransmitters. The device can
be mounted in any place by means of double-sided adhesive tape or wall plugs 5 x (3 x
30) mm. Mounting by means of wall plugs:
Remove push-buttons - to do it press a push-button on one side, and on the other
side put a screwdriver into a slot and lift it up.
Find a place on the wall to mount the transmitter, make two holes corresponding
mounting holes from the transmitter’s base.
Set wall plugs in the holes.
Fix the base by tightening the screws into wall plugs.
Place the push-buttons back.
BATTERY CHANGE
Battery discharge status is signalled by several LED red diode flashes during
transmission time.
Remove push-buttons (Fig. 1).
By means of a screwdriver lever up the printedcircuit board releasing the bottom
latch (Fig. 2) and remove it from the base.
Remove the battery from the latch. (Fig. 3)
Mount a new battery.
Watch battery polarisation marked on the latch. Wrong
battery mounting may cause device damage.
Put the removed printed-circuit board back in the base.
Place the push-buttons back.
CAUTION: While changing the battery, it is suggested to press any of the but-
tons for about 5 seconds before putting it into a latch. Next press transmission
button several times to check its operation. If the transmitter does not work
properly repeat the battery change procedure.
FUNCTIONING, MOUNTING ROP-02
Disconnect power supply by the phase fuse, the circuit-breaker or the switch-discon-
nector combined to the proper circuit.
Check if there is no voltage on connection cables by means of a special measure
equipment.
Connect the cables with the terminals in accordance with the installing diagram.
Install ROP-02 device in installation cable box.
Switch on the power supply from the mains.
The device can operate in five modes:
MONOSTABLE
the relay operates only while pressing transmitter’s push-button.
BISTABLE
(one push-button) the device changes relay status cyclically always after
pressing the same pushbutton.
SWITCH ON
the device switches on after pressing the pushbutton.
SWITCH OFF
the device switches off after pressing the pushbutton.
TIME
the device switches off according to the adjusted time (tp), but it may be
switched off before adjusted time finishes. Default settings - 15 seconds.
CAUTION! Adjusted time cannot be deleted.
MONOSTABLE
mode:
Press transmitter’s push-button for a longer time. Press PROG push-button of
ROP-02 device for a longer time until LED red diode switches on (constant signal).
Next release PROG push-button. Release transmitter’s push-button. LED red diode
switches on (first signal pulsates, next the signal is constant). Press the same trans-
mitter’s push-button and release it. LED red diode switches on (the signal pulsates)
and next the signal switches off - THE TRANSMITTER IS ADDED.
BISTABLE
mode:
Press PROG push-button of ROP-02 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button. Press the trans-
mitter’s push-button for a longer time. LED red diode switches on (first signal pul-
sates, next the signal is constant). Release transmitter’s push-button. LED red diode
switches on (the signal pulsates), next the LED red diode switches off - it means the
TRANSMITTER IS ADDED.
SWITCH ON/SWITCH OFF
mode (two push-buttons):
Press PROG push-button of ROP-02 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button. Press and release
transmitter’s pushbutton. LED red diode switches on (first signal pulsates, next the
signal is constant). Press and release the second transmitter’s push-button. LED red
diode switches on (the signal pulsates) and next it switches off - THE TRANSMITTER
IS ADDED.
TIME MODE
(one push-button):
Press PROG push-button of ROP-02 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button. Press and release
transmitter’s pushbutton. LED red diode switches on (the signal pulsates, next the
signal is constant). Press and release the same transmitter’s push-button. LED red
diode switches on (the signal pulsates) and next it switches off - THE TRANSMITTER
IS ADDED.
An exemplary programming procedure with the use of P-257/2 remote controller.
The procedure for the rest of radio EXTA FREE transmitters is analogous.
CAUTION: Every transmitter can cooperate with ROP-02 in a different mode,
depending on how they were added to the device. One transmitter can be added
during one programming cycle. Full memory is signalled with pulsating LED red
diode.
RADIO TRANSMITTERS POGRAMMING - CHANNEL 1
RADIO TRANSMITTERS POGRAMMING - CHANNEL 2
Press PROG push-button of ROP-02 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button. Wait (for about 5 sec-
onds) till LED red diode switches on (first signal pulsates, next the signal is constant).
Choose one out of five ROP-02 operating modes and programme the device in the
same way as for channel 1.
CAUTION: For the monostable mode, press the button
on the remote before pressing PROG push-button.
