PROGRAMMING “GLOBAL TIME”
Each new button assigned to a specific channel in the ROM-24 receiver in time mode operates using “global time”. By default the global time for all chan-
nels is set to 10 s. The user can change the global time value within the range from 1 s to 18 hours. After changing global time for the specific channel, the
buttons registered with this output in time mode will operate automatically with new value for global time. Exception: individual times assigned to buttons
during programming stage.
The global time value can be adjusted from the receiver using PROG button and also from mobile app if the receiver is paired with the EXTA LIFE controller.
PROGRAMMING GLOBAL TIME
using PROG button
Programming (changing) global time for the selected channel receiver
1. Briefly (1 s) press PROG button on the receiver; “CH1” LED lights up.
2. From the moment of „CH1” LED goes on, you have 2 s to briefly press PROG button to select channel number. The channel selection is signalled by
lighting up the correct LED (from CH1 to CH4).
3. After selecting the channel wait approx. 2 s for STATUS LED to light up.
4. After the STATUS diode lights up, wait approx. 5 s until the STATUS diode goes off.
5. After the LED turns off, briefly press PROG within 5 s. The STATUS LED will start blinking which signals time measurement.
6. After the time you want to program as the new „global time” has passed, again briefly press PROG.
7. The global time programming procedure is now complete which will be confirmed by blinking STATUS LED and the LED for the selected channel going
off.
Time assigned to a button can only be changed through its reprogramming.
REMOTE PROGRAMMING OF GLOBAL TIME
using mobile application
Remote change of global time for each of ROM-24 receiver’s output is also possible using mobile app. To do so, first pair the receiver with an EXTA LIFE
system controller. After successful pairing, ROM-24 receiver will be visible in the system as 4 channels (from Channel 1 to Channel 4). To set global time
for a channel, from the editing menu select “Configure”. You will be transferred to the configuration screen where you can set basic parameters for the
specific channel in the receiver.
For global time, set the “Global time” parameter. This parameter can be set from 1 s to 18 h using the following format — hour : minutes : seconds (xxh :
xxm :xxs).
SELECTIVE DELETION OF RECEIVER’S MEMORY
In the EXTA LIFE system receivers, you can use selectively delete buttons from the receiver’s memory. This enables you to delete only the selected but-
tons without the need to clear the complete memory of the receiver. You can delete buttons using the PROG button or remotely using the EXTA LIFE app.
DELETING RECEIVERS USING PROG BUTTON
1. Press the PROG button for approximately 5 s until STATUS LED lights up.
2. After the STATUS LED goes off, “CH1” LED will come on. You must then release the PROG button and in less than 2 seconds briefly press the PROG
button to select the number of channel to delete transmitter buttons. The channel selection is signalled by lighting up the correct LED (from CH1 to CH4).
3. After selecting the channel wait approx. 2 s for STATUS LED to light up.
4. Next, within less than 5 s you must briefly press the button assigned to the channel to be deleted from the receiver’s memory. If the button pair has been
assigned using on/off mode, just press one of these buttons.
5. Successful completion of the selective clearing is indicated by a series of quick blinks of STATUS LED and turning off the LED for the selected channel.
DELETING TRANSMITTERS USING EXTA LIFE APP (REMOTE)
The receiver from which you want to remotely delete receivers’ buttons must be paired with an EXTA LIFE controller. To remotely delete buttons from the
receiver’s memory, do the following:
1. From a receiver’s (channel) editing menu, select “Configure”
.
2. At the configuration screen, press the “Assigned transmitters”
to download the list of transmitters currently stored in the receiver’s memory
.
3. By pressing the name of a transmitter you can view details on the record in the receiver’s memory displayed its entry into the memory of the receiver
(numbers of entered keys, operating mode, assigned time for time mode).
4. By selecting “Delete” from the transmitter’s editing menu, you delete the transmitter buttons from the receiver’s memory (4). You can also delete a trans-
mitter by moving an element to the side.
REMOTE PROGRAMMING USING EXTA LIFE APPLICATION
The remote programming function for receivers enables you to assign the transmitter’s buttons to the selected receiver’s channel, without actual access to the
receiver, i.e. without the need to press the PROG button on the receiver). This is particularly convenient when the receivers are already installed in a location and
it is difficult to access them.
Requirements for remote programming transmitters with ROM-24 receiver:
- An EXTA LIFE controller installed in the system,
- The receivers you want to assign to the receiver are supplied with power and paired with a controller,
- The transmitters to be remotely assigned to receivers must be paired with the controller,
- During one step only one transmitter can be remotely assigned to a receiver.
To remotely assign selected buttons on a transmitter to the specific channel, do the following:
1. Pair the receiver with controller.
2. Pair the transmitter with the controller, this applies to the transmitter whose buttons you want to remotely assign to the receiver.
3. On the transmitter select “Assign receiver”
.
4. From the list of all paired receivers select the receiver (channel) to which you want to remotely assign the transmitter
.
5. In the „Operating Mode” field set the mode for use by the transmitter working with the receiver (channel)
. The available modes for ROM-24 are: on/off, bista-
ble, monostable, time.
6. Select the transmitter’s buttons for remote assignment to the receiver
. In case of time mode, you must also declare time assigned to the selected button. The
time range available is from 1 s to 18 h.
7. Pressing the “Transmitter preview” button brings up a transmitter’s view with button numbers shown
.
8. Press “Save” to remotely program the transmitter into the receiver. After the correct completion of the operation you will see the message “The devices have
been paired”.
Remote assignment of a transmitter to receiver can be also executed from the receiver level. In this situation, select “Assign transmitter” from the receiver’s (chan-
nel’s) editing menu.
If you are programming time mode, the following situations are possible:
1. “On button” and “off button” are the same — receiver (channel) activation and deactivation before the programmed period is executed using the same button
(in this example, it is “1” on the RNK-22 transmitter).
2. “On button” and “off button” are different — the “on” button only activates the receiver (channel) and “off” button only deactivates the device before the pro-
grammed time elapses.
3. “off button was not defined — the situation is the same as the one described in section 1.
7. After correct assignment of the button, several quick blinks of STATUS LED occur and the LED for specific channel in the receiver goes off.
After pairing the selected button on the transmitter with the channel on the ROM-24 receiver, the period assigned to this button takes the default value of
10 s (default global time). To change the time, carry out the time programming procedure (Step_2). With the ROM-24 receiver, you can assign individual
time to each button paired with selected channel. The time is programmable from 1 s to 18 h.
Step_2
: Programming the time assigned to the selected button in time mode
1. Briefly (1 s) press PROG button on the receiver; “Led_CH1” LED lights up.
2. From the moment of „Led_CH1” LED goes on, you have 2 s to briefly press PROG button to select channel number. The channel selection is signalled
by lighting up the correct LED (from LED_CH1 to LED_CH4).
3. After selecting the channel wait approx. 2 s for STATUS LED to light up.
4. After the STATUS diode lights up, wait approx. 5 s until the LED goes off.
5. After the LED goes off in less than 5 s, briefly press the transmitter button assigned to the selected channel in time mode. (This refers to the transmitter
you want to program time).
6. The STATUS LED will start blinking which signals time measurement.
7. After a period of time you want to assign to the specific button has passed, again briefly press the button on the transmitter selected previously.
8. The time programming procedure is now complete which will be confirmed by blinking STATUS LED and the LED for the selected channel going off.
Time assigned to a button can only be changed through its reprogramming.
