background image

1. MAINTAIN A SAFE WORK ENVIRONMENT

      Keep work area well lit. Make sure there is adequate surrounding work space.

2. DO NOT FORCE THE EQUIPMENT

      The Turn Tables will do the work better and safer below or at the weight capacity   

      (3,000 lbs. or 1.5 Tons per pair) for which they were designed. Do not exceed the  
      weight capacity. The Turn Tables will break under dynamic loading.

      Caution: Always be aware of Dynamic Loading. If you drop a weight on the Turn 

       

      Tables, it may create for a brief instant, an excess load. The Turn Tables are designed   
      for 3,000 lbs. or 1.5 Tons per pair maximum load; do not exceed.

3. MAKE SURE THE TURN TABLES ARE POSITIONED ON A DRY, FLAT, LEVEL   

     SURFACE

      Do not position the Turn Tables on an uneven surface or a surface covered with ice,   

      grease, oil, or any other substance that may cause the Turn Tables to tip over or slide  
      when driving a vehicle up onto the Turn Tables.

4. ADDITIONAL HELP MAY BE REQUIRED TO GUIDE THE VEHICLE ONTO THE  

     TURN TABLES

      Another person, standing a safe distance away from the vehicle, may be needed to act    
      as a visual guide as you drive the vehicle onto the Turn Tables.

5. ALWAYS MAINTAIN THE SLOWEST SPEED POSSIBLE WHEN DRIVING THE    

     VEHICLE ONTO AND OFF OF THE TURN TABLES

6. ONCE THE VEHICLE HAS BEEN POSITIONED ON THE TURN TABLES  

     IMMEDIATELY TURN OFF THE ENGINE, SET THE PARKING BRAKE, AND  

     BLOCK THE REAR TIRES

      Never attempt to use the Turn Tables while the engine is running. Turn off the engine,  

      set the parking brake, carefully exit the vehicle, and block the rear tires with wheel  
      chocks or blocks of wood to prevent the vehicle from rolling while being serviced.

7. NOTE

      It is recommended that the vehicle manufacturer’s manual, and/or a qualified    

      technician, be consulted to determine the front end wheel alignment degree of  
      tolerance difference allowable for the vehicle make and model being tested.

8. NEVER WORK UNDERNEATH A VEHICLE WITHOUT USING ADDITIONAL    

     SAFETY SUPPORT DEVICES (I.E., JACK STANDS) TO SUPPORT THE VEHICLE.

      The Turn Tables are not designed to be used with jack stands and no one should    

      work under vehicle while vehicle is on Turn Tables.

SPECIFIC PRODUCT WARNINGS 

& PRECAUTIONS

4

© Zackman Scientific

  

Summary of Contents for ZAWG008













Reviews: