background image

 

    

CONFIDENTIAL

                             Z3-DM8148-MC-RPS V2.00.02  

 
 

___________________________________________________________________________________________ 

Z3 Technology, LLC 

 100 N 8

th

 ST, STE 250 

 Lincoln, NE 68508-1369 USA 

 +1.402.323.0702 

37 

PMU: registered new PMU device of type 0 omap-iommu omap-iommu.0: ducati registered 
omap-iommu omap-iommu.1: sys registered 
squashfs: version 4.0 (2009/01/31) Phillip Lougher 
JFFS2 version 2.2. (NAND)  © 2001-2006 Red Hat, Inc. 
msgmni has been set to 180 
io scheduler noop registered 
io scheduler deadline registered 
io scheduler cfq registered (default) 
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled 
omap_uart.0: ttyO0 at MMIO 0x48020000 (irq = 72) is a OMAP UART0 console [ttyO0] 
enabled, bootconsole disabled console [ttyO0] enabled, bootconsole disabled 
omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 
omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 
omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 
omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 
omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 
brd: module loaded 
loop: module loaded 
ahci probe: devid name is ahci 
ahci CAP register dump =0x6726ff80 
Modified ahci CAP register dump =0x6f26ff80 ahci ahci.0: forcing PORTS_IMPL to 0x1 
ahci: SSS flag set, parallel bus scan disabled ahci ahci.0: AHCI 0001.0300 32 slots 1 
ports 3 Gbps 0x1 impl platform mode ahci ahci.0: flags: ncq sntf stag pm led clo only 
pmp pio slum part ccc apst scsi0 : ahci_platform 
ata1: FORCE: link flag 0x6 forced -> 0x6 
ata1: FORCE: link flag 0x4 forced -> 0x6 
ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a150fff] port 0x100 irq 16 omap2-nand 
driver initializing 
omap2 driver probed 
NAND device: Maf ID: 0xec, Chip ID: 0xda (Samsung, ) 
erasesize: 0x20000, writesize: 2048, oobsize: 64 Scanning device for bad blocks Bad 
eraseblock 118 at 0x000000ec0000 Bad eraseblock 169 at 0x000001520000 Bad eraseblock 677 
at 0x0000054a0000 Bad eraseblock 733 at 0x000005ba0000 Bad eraseblock 806 at 
0x0000064c0000 Bad eraseblock 1479 at 0x00000b8e0000 Bad eraseblock 1929 at 
0x00000f120000 Creating 8 MTD partitions on "omap2-nand.0": 
0x000000000000-0x000000080000 : "U-Boot-min" 
0x000000080000-0x0000001c0000 : "U-Boot" 
0x0000001c0000-0x000000240000 : "U-Boot-min Copy" 
0x000000240000-0x000000260000 : "U-Boot Env Copy" 
0x000000260000-0x000000280000 : "U-Boot Env" 
0x000000280000-0x0000006c0000 : "Kernel" 
0x0000006c0000-0x00000cee0000 : "File System" 
0x00000cee0000-0x000010000000 : "Reserved" 
NAND: size is 256 
UBI: attaching mtd6 to ubi0 
UBI: physical eraseblock size: 131072 bytes (128 KiB) 
UBI: logical eraseblock size: 126976 bytes 
UBI: smallest flash I/O unit: 2048 
UBI: VID header offset: 2048 (aligned 2048) 
UBI: data offset: 4096 
ata1: SATA link down (SStatus 0 SControl 300) 
UBI: max. sequence number: 5 
UBI: attached mtd6 to ubi0 
UBI: MTD device name: "File System" 
UBI: MTD device size: 200 MiB 
UBI: number of good PEBs: 1595 

Summary of Contents for Z3-DM8148-MC-RPS













































Reviews: