Owner’s Manual
TX107 Aluminum XL Folding Arch Ramps
Page
Check for parts online at
www.yutrax.com
or call 800-345-6007 M-F 8-5 CST
WARNING
READ, UNDERSTAND AND follow All ASSEMBlY,
INSPECTIoN, & USE INSTRUCTIoNS PRoVIDED
BEfoRE EACH USE. fAIlURE To follow All
INSTRUCTIoNS, wARNINgS & loAD CAPACITY RATINg
CoUlD RESUlT IN SERIoUS INJURY oR DEATH.
If ANY INSTRUCTIoNS ARE NoT UNDERSTooD oR If
YoU HAVE A PARTS ISSUE CAll 800-345-6007 BEfoRE
USINg.
Do NoT USE AN ATV oN THIS RAMP If THE ATV
HAS SNow CHAINS oN TIRES. CHAINS wIll CAUSE
DAMAgE To YoUR RAMP AND IS HAZARDoUS!
BE CAREfUl of PINCH PoINTS AT RAMP HINgE
loCATIoNS.
BE CAREfUl of PINCH PoINTS AT RAMP TAB
loCATIoNS wHIlE SECURINg RAMP To TAIlgATE.
THIS RAMP IS foR USE wITH 4-wHEElED ATV’S AND
lAwN TRACToRS oNlY. Do NoT USE wITH 2- oR 3-
wHEElED VEHIClES oR VEHIClES EXCEEDINg 1,500
lBS.
SAfETY STRAPS MUST BE SECURElY HooKED UP
To VEHIClE To PREVENT RAMPS fRoM SlIDINg
off TAIlgATE. TEST BEfoRE USINg oR YoU CoUlD
BE SERIoUSlY INJURED. BE SURE YoUR TRUCK IS IN
PARK AND EMERgENCY BRAKE ENgAgED.
BE SURE 4-wHEElED ATV oR lAwN TRACToR IS
CENTERED oN RAMPS. Do NoT USE wITH ANY
VEHIClE THAT HAS wIDER TIRES THAN THE RAMP
wIDTH.
MAXIMUM USABlE HEIgHT, gRoUND To loADINg
PoSITIoN, IS No MoRE THAN oNE HAlf THE lENgTH
of THE RAMP.
BE SURE RAMPS ARE PRoPERlY PlACED AND SECURED
AS DESCRIBED IN loADINg INSTRUCTIoNS.
Do NoT USE oN SofT SURfACES oR UNlEVEl
TERRAIN.
REAR ENgINE EQUIPMENT SHoUlD BE loADED IN
REVERSE To AVoID fRoNT END REAR-UP.
Do NoT EXCEED THE CAPACITY of YoUR loADINg
SURfACE (I.E. TAIlgATE, BUMPER). If UNKNowN,
CoNSUlT THE MANUfACTURER To fIND loAD
CAPACITIES.
If loADINg oR UNloADINg fRoM A TRAIlER, MAKE
SURE THE TRAIlER IS PRoPERlY CoUPlED To THE
Tow VEHIClE.
NEVER STAND IN THE PATH of EQUIPMENT wHEN
loADINg/UNloADINg wITH THE RAMP, AND KEEP
BYSTANDERS AwAY fRoM THE RAMPS.
Do NoT STEP BETwEEN RUNgS. THIS MAY CAUSE A
PERSoN To fAll THRoUgH AND PoSSIBlY RESUlT IN
SERIoUS BoDIlY INJURY.
RAMPS ARE INTENDED foR loADINg/UNloADINg
EQUIPMENT oNTo A TRAIlER oR PICKUP TRUCK. Do
NoT USE RAMP SECTIoNS AS A lADDER, BRIDgE,
SCAffolDINg, oR foR ANY oTHER PURPoSE.
YUTRAX offers a full line of ATV accessories. We appreciate
your purchase of one of our world class ATV Ramps. Follow
these few simple instructions and your product will be sure
to give you many years of trouble free pleasure. Instructions
should be kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product,
Do
NoT return to the retailer
; contact the YUTRAX customer
service department at 800-345-6007 Monday through Friday
from 8 a.m. to 5 p.m. CST for assistance.
ASSEMBLY INSTRUCTIONS:
1. Attach the two provided securing straps to the center
brace, approximately 16" from the tailgate end (one
on each ramp). Wrap the loop end of each strap
around the center brace and thread the buckle and
“S” hook end thru the loop. This permanently attaches
straps to the ramp.
SEE fIgURE 1
.
USE INSTRUCTIONS:
TO LOAD YOUR 4-WHEELED ATV OR LAWN TRACTOR:
1.
On level ground, rest both ramps on the tailgate.
SEE
fIgURE 2
. Be sure ramps are centered on tailgate and
aligned correctly to your four-wheeled ATV or lawn
tractor’s wheel width.
. Hook the “S” hooks of both straps to bumper and pull
on loose end of straps until straps are tightly holding
ramp to tailgate. Be sure ramps have not moved location
when tightening straps. Double check to make sure ramps
are still aligned correctly. To remove, simply push the
thumb release on strap buckle.
3. Using an electric or manual winch, draw the ATV or lawn
tractor up the ramps.
Do NoT drive the ATV or lawn
tractor up the ramps.
4. Once vehicle is in truck bed, be sure to set brake
& securely tie down vehicle. Ramp can now be
removed, folded up, and stored.
TO UNLOAD YOUR 4-WHEELED ATV
OR LAWN TRACTOR:
S
Figure 1
bumper
s-hook
loop
tailgate
1. Reverse loading procedures to unload your ATV or
lawn tractor.
