background image

26

Use only the electrolyte container that comes 
with the battery.

Sealed VRLA battery  electrolyte 

is a higher concentration of sulfuric acid.  All sealed 
VRLA  battery  electrolyte containers aren’t the same.  
Each contains the proper amount of electrolyte for its 
specific battery.

Always wear plastic gloves and protective 
eyewear.

No Smoking, see page 9 for full safety 

instructions.Of course, don’t forget safety precautions 
when storing or handling electrolyte solution.

Activating sealed VRLA  batteries is easy, although a little
different from conventional activation.  For problem-free
start-up  and operation, follow the procedure outlined
here.  A few things to keep in mind before you get rolling:

Store the battery in a cool, dry place out of 
direct sunlight.

Do not remove the foil sheet covering the 
filler port until activation.

After removing the electrolyte container cap 
strip, do not peel, pierce or otherwise open 
the sealed electrolyte receptacles.  Don’t 
separate the individual cells.

Read electrolyte handling instruction and 
precautions on the label.

Activation and Installation

✘ ✘

Save

this

strip

5

SECTION

Sealed VRLA
Batteries

To Activate a Sealed VRLA
Battery

1.

Place the battery on a level surface.  Battery must be

out of the vehicle.

2.

Remove electrolyte container from vinyl bag.  Remove

the strip of caps.  

Put the strip aside – you’ll use

this later as the battery sealing plug.

Use only

the dedicated container that comes with the battery.  It con-
tains the proper amount of electrolyte for your specific
model – important to service life and operation.  Do not
pierce or otherwise open the sealed cells of the electrolyte
container.  Do not attempt to separate individual cells.

3.

Place electrolyte container, sealed top of the cells down,

into the filler ports of the battery.  Hold the container level,
push down to break the seals.  You’ll see air bubbles as the
ports fill.  

Do not tilt the electrolyte container.

Warning: Improper activation or excessive
overchargering (possibly by equipment
failure) could cause damage to the battery
or vehicle by forcing acid out of the
safety vent.

See next page.

Summary of Contents for SmartShot Automatic 12V 1.5 Amp 5 Stage













































Reviews: