background image

- 19 - 

 

 
 
 
 
 

Warranty 

For one year from the date of purchase YTL International will replace for the original purchaser, or repair 
the plug aerator.    The warranty will not apply to any unit which was not assembled correctly, misused, 
overloaded or which has been used or operated contrary to our instructions, or which has been repaired 
or altered by anyone other than an authorized representative.   
 

Warranty Exclusions 

This warranty does not cover cosmetic defects such as paint, decals or wear items such as tires.    This 
warranty will not cover failures or problems due to acts of God, or events or forces beyond the control of 
the manufacturer.       

 

 

Normal Wear Exclusion 

The aerator needs periodic service to perform well. This warranty does not cover repair when normal 
use has exhausted the life of a part or the equipment as a whole. 

 
Installation, Use and Maintenance Exclusion 

This warranty will not apply to parts and/or labor if the aerator has been misused, neglected, involved in 
an accident, abused, loaded beyond its limits, modified or assembled incorrectly.    Normal maintenance 
is not covered under this warranty. 

 
Limits of Implied Warranty and Consequential Damage Exclusion 

YTL International disclaims any obligation to cover any loss of time, use of this product, freight, or any 
incidental or consequential claim by anyone from using this aerator.    THIS WARRANTY IS IN LIEU OF 
ALL 

OTHER  WARRANTIES, 

EXPRESS 

OR 

IMPLIED, 

INCLUDING  WARRANTIES 

OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR. 
 
An  exchange  unit  will  be  subject  to  the  original  warranty.    The  length  of  the  warranty  governing  the 
exchanged unit will have the date as the purchase date of the original unit.    This warranty gives  you 
certain legal rights which may change from state to state. Your state may also have other rights you may 
be entitled to that are not listed within this warranty. 

 
Contact Information 

YTL International 
17517 Fabrica Way, Suite J 
Cerritos, CA    90703 
Phone: (888) 723-6534 
Phone: (562) 404-8016 
Fax: (562) 404-8013 
 
 
 
 
 
 
 
 
 

Limited Warranty 

Summary of Contents for YTL31102




















Reviews: