background image

YT-700 series 

 

1. Introduction 
 

1.1 

General Information for the users 

Thank you for purchasing Young Tech Co., Ltd products.  Each product has been fully 

inspected after its production to offer you the highest quality and reliable performance.  

Please read the product manual carefully prior to installing and commission the product.     

  For the safety, it is important to follow the instructions in the manual.    Young Tech Co., 

Ltd will not be responsible for any damages caused by user’s negligence.     

 

The manual should be provided to the end-user.   

  Any modifications or repairs to the product may only be performed if expressed in this 

manual.  

  The manual can be altered or revised without any prior notice.  Any changes in 

product’s specification, design, and/or any components may not be printed immediately 

but until the following revision of the manual.     

  The manual should not be duplicated or reproduced for any purpose without prior 

approval from Young Tech Co., Ltd, Gimpo-si, South Korea.   

 

1.2 Manufacturer 

Warranty 

  For the safety, it is important to follow the instructions in the manual.    Manufacturer will 

not be responsible for any damages caused by user’s negligence.   

  Manufacturer will not be responsible for any damages or accidents as a result of any 

alteration or modification of the product and its parts.    If any alteration or modifications 

are necessary, please contact Young Tech Co., Ltd directly.     

  Manufacturer warrants the product from the date of original purchase of the product for 

one (1) year, except as otherwise stated. 

  Manufacturer warranty will not cover products that have been subjected to abuse, 

accidents, alterations, modifications, tampering, negligence, misuse, faulty installation, 

lack of reasonable care, repair or service in any way that is not contemplated in the 

documentation for the product, or if the model or serial number has been altered, 

tampered with, defaced or removed; damages that occurs in shipment, due to act of 

God, failure due to power surge, or cosmetic damage.  Improper or incorrectly 

performed maintenance will void this limited warranty.     

 

For detailed warranty information, please contact Young Tech Co., Ltd – South Korea.   

 

1.3 

Explosion Proof Warning 

Please ensure the unit is being used and installed within the explosion proof certified 

environment.   

 

YT-700 series explosion proof grades are 

Ex d IIC T6 

and can be used in 

zone 1.   

 

  Explosion proof type of cables and gaskets should be used, when explosion gases are 

Summary of Contents for YT-700 Series















Reviews: