manualshive.com logo in svg

YSI PRO20, User Manual

Share
Download
YSI PRO20 User Manual Download Page 34

28

air. If the connector is corroded, contact YSI Technical Support or the 
Authorized dealer where you purchased the instrument.  

Remove sensors upside down (facing the ground) to help 
prevent water from entering the port upon removal. 

i

SENSOR MAINTENANCE

Sensor Maintenance - Temperature

You must keep the temperature portion of the sensor free of build up. 
Other than that, the sensor requires no maintenance. A toothbrush can 
be used to scrub the temperature sensor if needed.
 

Sensor Maintenance - Dissolved Oxygen  

Membrane Cap Installation

The DO sensor (Polarographic and Galvanic) is shipped with a dry, 
protective red cap that will need to be removed before using. Remove 
the protective cap or used membrane cap and replace it with a new 
membrane cap following these instructions: 

Remove the sensor guard to access the sensor.

Remove the protective red cap or unscrew and remove 
any old membrane cap by holding the sensor when 
unscrewing the membrane cap and discard. 

Thoroughly rinse the sensor tip with distilled or 
deionized water.

   

Fill a new membrane cap with O

2

 sensor 

solution that has been prepared according 
to the directions on the bottle. Be very 
careful not to touch the membrane surface.

Lightly tap the side of the membrane cap to 
release bubbles that may be trapped.

Summary of Contents for PRO20















































Reviews:

No comments

Brands by name

Popular brands

Load more brands