YSI ADA-WA 1 Installation Instructions Manual Download Page 6 | Manualshive

Page: 6 / 11

YSI ADA-WA 1 Installation Instructions Manual Download Page 6

Installation recommendations

ADA-WA 1; ADA-WA 4

6

ba76071e01

02/2012

Special installation recommendations:
VisoTurb 700 IQ and ViSolid 700 IQ

Note

Please also observe the general basic information in the
I

NSTALLATION

chapter of the sensor operating manual. There

you will find important notes on optimizing the installation.

45 ° pipe installation



Pipe diameter at the installation location of at least DN 80.
The pipe should be straight and not tapered for a length
of at least 50 cm (VisoTurb 700 IQ) or 25 cm
(ViSolid 700 IQ) in the direction of observation. Angled or
tapered pipes can cause interference effects in the case
of low turbidity.



The front part of the sensor is pitched towards the flow.
Exception:
If there are high quantities of foreign bodies with fibrous
or large surfaces, as for example hairs, strings or leaves,
it may be of advantage to incline the sensor in the
direction of the flow so that the sapphire disc does not
face the flow.

Min. 80 mm

ESS/WA...

WA 700/...

Marking aid in
this direction

Flow

direction

ADA-WA1

straight pipe

VisoTurb: min. 50 cm
ViSolid: min. 25 cm

«
...
4
5
6
7
8
...
»

Summary of Contents for ADA-WA 1












Reviews:

No comments