background image

 

 

 

CLEANING INSTRUCTIONS 

 
NOTE: Before they can be serviced, equipment exposed to biological, radioactive, or toxic 
materials must be cleaned and disinfected.

 Biological contamination is presumed for any 

instrument, probe, or other device that has been used with body fluids or tissues, or with waste water. 
Radioactive contamination is presumed for any instrument, probe or other device that has been used 
near any radioactive source. 
 
 If an instrument, probe, or other part is returned or presented for service without a Cleaning 
Certificate, and if in our opinion it represents a potential biological or radioactive hazard, our service 
personnel reserve the right to withhold service until appropriate cleaning, decontamination, and 
certification has been completed. We will contact the sender for instructions as to the disposition of 
the equipment. Disposition costs will be the responsibility of the sender. 
When service is required, either at the user's facility or at YSI, the following steps must be taken to 
insure the safety of our service personnel. 
 

1.

 

In a manner appropriate to each device, decontaminate all exposed surfaces, including any 
containers. 70% isopropyl alcohol or a solution of 1/4 cup bleach to 1 gallon tap water is suitable 
for most disinfecting. Instruments used with waste water may be disinfected with 0.5% Lysol if 
this is more convenient to the user. 

2.

 

The user shall take normal precautions to prevent radioactive contamination and must use 
appropriate decontamination procedures should exposure occur. 

3.

 

If exposure has occurred, the customer must certify that decontamination has been accomplished 
and that no radioactivity is detectable by survey equipment. 

4.

 

Any product being returned to the YSI Repair Center, should be packed securely to prevent 
damage. 

5.

 

Cleaning must be completed and certified on any product before returning it to YSI. 

 

PACKING INSTRUCTIONS 

 

1.

 

Clean and decontaminate items to insure the safety of the handler. 

2.

 

Complete and include the Cleaning Certificate. 

3.

 

Place the product in a plastic bag to keep out dirt and packing material. 

4.

 

Use a large carton, preferably the original, and surround the product completely with packing 
material. 

5.

 

Insure for the replacement value of the product. 

YSI Incorporated 

YSI 58 DO Meter 

26 

Summary of Contents for 58









































Reviews: