If the Master phone is lost or you want to set up YOYOCam again from the beginning, you can
use Factory Reset to set all settings and parameters back to the factory default. Following Factory
Reset you will need to set the Master user, re-enter any mobile network(MMS, Email) settings and
reconfigure all users etc. To perform Factory Reset:
1.
Make sure YOYOCam is switched on, status
armed or
disarmed.
2.
Press and hold the Reset key for 5 seconds until YOYOCam beeps.
3.
You may now release the Reset key. Factory Reset is complete.
Alternatively, the Master can send #19#Password#
Reset
key
YOYOCam G33 - Complete Command List
Arm (active 20 seconds after command received)
#01#
Disarm
#02#
ARM AND DISARM (Master & User)
Capture & send back to me by MMS
#03#
Capture & send to Number by MMS
#03#Number#
Capture & send to Master Email
#05# (Sent by Master)
Capture & send to Master Email and User Email List
#05# (Sent by User)
Capture & send to EmailAddress
#05#EmailAddress#
GET IMAGE (Master & User)
Set me as Master (out of box / after factory reset)
#00#
Master - transfer to a new phone number
#14#NewMasterNumber#
Set/update Master’s Email address
#09#EmailAddress#
Delete Master’s Email address
#09#
DEFINE MASTER
Add User (UserNumber = User’s mobile number)
#07#UserNumber#
Add Email to User Email List
#07#EmailAddress#
Delete User
#27#UserNumber#
Delete all Users and User Email List
#27#
Change Password
#18#OldPassword#NewPassword#
DEFINE USERS
Warning tone upon alarm - OFF
#30#0#
Warning tone upon alarm - on
#30#1#
SMS alert upon alarm - off
#11#0#
SMS alert upon alarm - ON
#11#1#
Message upon alarm - off
#12#0#
MMS upon alarm – ON
(Contains images as per
IMAGE SETTINGS below)
#12#1#
Email upon alarm – off
(Contains images as per
IMAGE SETTINGS below)
#12#2#
Telephone call at Alarm - OFF
#13#0#
Telephone call at Alarm - on
#13#1#
SMS to Users - OFF
#32#0#
SMS to Users - on
#32#1#
Message to Users - OFF
#33#0#
Message to Users – on
(Contains images as per
IMAGE SETTINGS below)
(MMS to Users or Email to User Email List,
with images, as set by #12# above)
#33#1#
ALARM NOTIFICATIONS
Note:
CAPITALS (eg. OFF) denote default setting
Get temperature from plug-in sensor
#15#
Set temperature range to monitor
#16#LoTemp#HiTemp#
Temperature alert - OFF
#15#0#
Temperature alert - on
#15#1#
TEMPERATURE SENSOR
Scheduled arm/disarm - setting
#41#Day#ArmTime#DisarmTime#
Scheduled arm/disarm - OFF
#04#0#
Scheduled arm/disarm - on
#04#1#
Scheduled image capture & send - setting
Mode: 0 - Email; 1 - MMS
#43#Mode#Day#StartTime#EndTime#Interval#
Scheduled image capture & send - OFF
#06#0#
Scheduled image capture & send - on
#06#1#
SCHEDULED ACTIONS
Number of images in alarm message (1 to 5); default 3
#21#Quantity#
Size of image in alarm, get image or scheduled
#22#Quality#
capture & send. Quality 1: Low (320 x 240),
2: Medium (640 x480), 3: High (1280 x 768)(default)
IMAGE SETTINGS
off (never turned on)
#20#0#
AUTO mode (on when dark and motion detected)
#20#1#
Always (on whenever motion detected, even in bright light)
#20#2#
LED LIGHTING SETTINGS
Get status
#10#
Technical status report (firmware version, IMEI, signal)
#40#
GET STATUS
Infrared body detector - off
#17#0#
Infrared body detector - ON
#17#1#
LED status indicator - off
#31#0#
LED status indicator - ON
#31#1#
Power change notification SMS - off
#35#0#
Power change notification SMS - ON
#35#1#
Language – English
#36#1#
Language – SWEDISH
#36#2#
Weak signal alert by SMS – OFF
#37#0#
Weak signal alert by SMS – on
(requires enough signal to send an SMS)
#37#1#
Forward SMS from unknown numbers to Master – ON
#50#0#
Forward SMS from unknown numbers to Master – off
#50#1#
Auto disarm after repeated alarms – OFF
#55#0#
Auto disarm after n alarms – on
#55#n#
ADVANCED SETTINGS
Day:
0 - Every day; 1 - Mon; 2 - Tue; 3 - Wed; 4 - Thu; 5 - Fri; 6 - Sat; 7 - Sun; 8 - Mon-Fri; 9 -
Weekend (Sat+Sun)
Check Email parameters
#26#
Configure Email sending parameters (Gmail)
#62#gmail#EmailAddress#Password#
Configure Email sending parameters
#62#outlook#EmailAddress#Password#
(Outlook.com, Hotmail)
Configure Email sending parameters (other)
#26#SenderAddress#password#STMPserver#
SMTP port#SSL#TLS#
CONFIGURE EMAIL SERVICE
MMS: Get current settings
#25#
MMS: Configure parameters
#25#MMSC#GatewayIP#WAPGatewayPort#
HTTPGatewayPort#APN#APNusername#APNpassword#MMS#
Internet: Get current settings
#24#
Internet: Configure parameters
#24#APN# APNusername#APNpassword#MCC#MNC#
DataProxyIP#DataProxyPort#DEFAULT#
Reset MMS and Internet
#54#
settings to default
Remote restart (reboot)
#42#password#
Factory reset (wipes all settings and data
#19#Password#
except wireless sensors and remotes).
RESET
Note:
Internet service must also be configured to be able to send Email.
CONFIGURE MMS AND INTERNET SERVICE
YOYOCam automatically configures MMS and Internet settings for most networks in Scandinavia,
Germany, France, Italy and Spain. Settings for other networks can be configured
manually – see the User Guide.
Factory Reset