STEP 1. Prepare YOYOCam G33
1.
To attach the antenna, align the plug with the antenna connector and screw it on gently by
hand until it is finger tight. Do not use tools. To remove it, gently unscrew the nut by hand.
2.
Press gently on the raised dots and slide the cover downwards.
3.
Lift the battery cover away from the device.
Battery
4.
Move the battery out of the way as shown.
5.
Insert the SIM card as indicated in the picture below.
•
NOTE:
The SIM PIN must be disabled. Use a mobile phone to check and, if necessary,
turn off SIM Lock.
•
NOTE:
Check that the SIM card has credit and is enabled for MMS and mobile internet.
a)
Slide the clip upwards in the
direction of the OPEN arrow (
1
).
b)
Lift the clip (
2
).
c)
Locate the SIM card in the
holder, gold contacts facing
down. Be careful not to push
the SIM card past the clip so
that it ends up inside YOYOCam.
d)
Close the metal clip (
3
).
e)
Slide the clip downwards (
4
) in
the direction of the LOCK arrow.
TIP
: Pressing lightly on each side of the metal clip makes
it easier to click open and shut.
YOYOCam uses a standard size
SIM Card (not micro or nano size)
WARNING:
Always be sure to switch off
YOYOCam and disconnect the power before
inserting or removing the SIM card. Do not touch
the gold contacts of the SIM Card.
6.
7/8.
Temperature
sensor
6.
Insert the power connector and lead the power cable out to the left or right, as required.
7.
Replace the battery. Locate the back cover as shown. Press upwards at the two points
indicated (not in the centre) to click it in to place.
8.
Plug in the temperature sensor, if required. Use a standard 3.5mm stereo audio extension
cable if you wish to locate the sensor away from YOYOCam.
1.
Mount the bracket on the wall, ceiling or other surface as required.
2.
Attach YOYOCam to the threaded tip of the bracket.
3.
Screw the round lock-nut towards YOYOCam to secure YOYOCam on the mount.
4.
Loosen the screw so that the angle can be adjusted. (See illustration opposite).
5.
Tighten the screw to fix YOYOCam in the desired position.
STEP 2. Mount YOYOCam G33
BUILT IN STAND
Un-clip the stand and rotate backwards. See illustration opposite.
MOUNTING BRACKET
STEP 3. Set Up YOYOCam G33
1.
Plug the power adaptor in to an outlet.
2.
Slide the power switch to the ON position to turn on YOYOCam.
3.
After approximately 60 seconds, YOYOCam bleeps to indicate that the mobile network has
been found.
4.
From your mobile phone, send an SMS with text
#00# to the
mobile number of YOYOCam’s SIM card. YOYOCam confirms
your phone as Master by SMS,
meaning that you have full
control over YOYOCam.
5.
The SMS responses are in
Swedish by default.
Send
#36#1# to switch to English.
6.
Arm YOYOCam
•
Send an SMS with text
#01# to arm YOYOCam
•
Send an SMS with text
#02# to disarm YOYOCam
ON
OFF
In the armed state, YOYOCam raises an alarm when the built-in infrared body sensor detects
movement. When the alarm is raised, YOYOCam sends an SMS to the Master followed by an
MMS with images. Alternatively, the images can be sent to pre-set E-mail addresses or
YOYOCam can make a call to pre-set telephone number. Image and alarm settings can be
configured – see
Using YOYOCam G33 and Complete Command List.
Using YOYOCam G33
The easiest way to drive YOYOCam is to install our app
YOYOCam 3G Indoor from the App
Store
SM
or Google Play
TM
. You can also drive YOYOCam from any kind of mobile phone via SMS
commands.
The default Password is 1234. Change the Password to your own 4-digit number, for example:
• #18#1234#0678# changes the default Password to 0678
As Master, you can add up to 4 Users who can arm/disarm YOYOCam and request images:
•
#07#UserNumber# adds UserNumber, for example #07#+46701234567#
•
#27#UserNumber# deletes UserNumber
Master and Users may arm and disarm YOYOCam:
•
#01# arms YOYOCam. Infrared body sensor is activated after a 20 second delay is
received.
•
#02# disarms YOYOCam. Infrared body sensor is turned off.
Master and Users can request an image to be sent using MMS:
•
#03# sends the MMS to the requestor (Master or User)
•
#03# Number# sends the MMS to Number (does not need to be a User)
• Default image quality is High (1280 x 768)
Master and Users can call YOYOCam and listen in via the built-in microphone.
• The caller must send (i.e. not withhold) the mobile number on voice calls. YOYOCam
rejects withheld and unknown numbers with busy-tone.
Users do not receive alarms by default. The Master can enable alarms to users:
•
#32#1# enables SMS alarm to Users; #32#0# turns it off
•
#33#1# enables alarm images to Users; #33#0# turns it off
• By default YOYOCam sends 3 images at High quality (1280 x 768) using MMS.
YOYOCam automatically configures MMS and Internet settings for most networks in
Scandinavia, Germany, France, Italy and Spain. Settings for other networks can be
configured manually.
To send images using Email, YOYOCam must be configured with settings for Internet, Email
sender address and Email Server. The simplest way is to create a new Gmail or Outlook.com
account for YOYOCam, then send the Email address and password:
• #62#gmail#EmailAddress#Password# for a Gmail account.
• #62#outlook#EmailAddress#Password# for an Outlook.com or Hotmail account.
You may need to additionally go in to the account settings for the Gmail or Outlook.com account
and enable SMTP.
For other Email services, please ask your provider for the parameters needed to send Email:
• #26#SenderAddress#Password#SMTPserverAddress #SMTP-port#SSL#TLS#
Note that SenderAddress might be a username. SMTP-port is usually 25, 465 or 587. SSL and
TLS take values 0 (OFF) or 1 (on).
YOYOCam is now operational.
Standard
Micro
Nano