Young Electric Mate Manual Download Page 12

 

 

Do not overload beyond the bike rack’s weight capacity of 200lbs. 

 

Do not carry more than 2 bikes on the carrier. 

 

The bike rack is not intended for transporting humans or animals. 

 

If you are planning to load only one bike, it is recommended to place it in the position closest to the vehicle.   

 

All bikes must be secured properly before operating the vehicle. 

 

Make sure the front of the bike(s), when mounted, are at or above the bottom of the bumper to avoid damage to the bike(s). 

 

Do not carry flammable items on the bike rack. 

 

If using the bike rack to transport electric bicycles, please remove the batteries from the bicycles prior to transporting them. This will 

help reduce the weight supported by the carrier.   

 

During long trips, frequently check the straps and bike position, especially if traveling on rough terrain. 

 

Please do not make alterations to the product, as it can pose potential hazards to your safety. 

 

Failure to heed these warnings may result in personal injury and/or property damage. 

 

To prevent serious injury or death, inspect the bike rack for any signs of wear, corrosion and fatigue before each use. Do not use the 

bicycle rack if parts are bent, broken, deformed or missing. If parts are bent, broken, damaged or missing, remove the rack from your 
vehicle before operating the vehicle. 

 WARNINGS 

 

Summary of Contents for Mate















Reviews: