Bluetooth™
The EXM MobileSUB is capable of streaming
audio from Bluetooth™ enabled devices and
supports wireless ‘stereo’ pairing between two
EXM MobileSUBs. In Bluetooth™ stereo mode,
the first unit acts as the “Primary,” playing the
left audio channel and additional units are
“Secondary” (playing the right channel). The
audio source needs to be connected to the
Primary EXM MobileSUB unit.
Operation:
When the EXM MobileSUB is
powered on, Bluetooth™ is disabled by default.
To connect a device, tap the Bluetooth™
button. If a device has been previously
connected, it will attempt to reconnect. If a
wireless stereo connection was used, both
EXM MobileSUB units will try to re-establish
the wireless stereo connection (the same
Primary/Secondary roles re-established).
Pairing:
Press the Bluetooth™ button down
and hold for 4 seconds, then release.
Status:
The blue LED indicates the status of
the Bluetooth™ connection, please refer to the
chart in the Owner’s Manual for more detail.
Level:
Streamed music’s volume can be
changed via the connected Bluetooth™ device
or channel 3’s Level control. Channel 3’s
Level setting controls the maximum level a
connected device can set.
Stereo Mode:
Wireless stereo playback is
supported between two EXM MobileSUBs. One
acts as the Primary unit while another acts as a
Secondary unit. The Primary unit plays the left
audio channel while the Secondary unit plays
the right. The source device only connects to the
Primary unit, not the Secondary.
To enable Stereo Mode, double tap the
Bluetooth™ button on the EXM MobileSUB
used as the Primary unit (left), then double tap
the Bluetooth™ button on the secondary EXM
MobileSUB (right). The first unit double tapped
becomes the Primary unit (left).
New devices can still be paired to a Primary
unit if it’s in Stereo Mode. Pairing a device to
an EXM MobileSUB that is in Secondary mode
will end the stereo wireless connection.
Button Operation:
Single Tap:
Enables Bluetooth™
Double Tap:
Enter Stereo Mode
Press and Hold (4 seconds):
Enter Pairing Mode
Press and Hold (8 seconds):
Disables Bluetooth™
Range:
The EXM’s Bluetooth™ operating
range is rated for 10 meters (33 feet) line
of sight. The link’s quality can be affected
by excess wireless traffic in the 2.4 GHz
bandwidth or structures between the
Bluetooth™ unit and the streaming device.
Note: When connected with Bluetooth™,
ALL audio is streamed from your device.
If you don’t want the streaming music to
be interrupted, turn off ‘notifications’ on
your device.
Controls & Input/Output
Input Jacks:
The source should go directly
to the EXM MobileSUB and then looped to the
full-range loudspeakers using the High Pass
Output jacks, this ensures an ideal crossover
to the full-range loudspeakers. These jacks
can be fed with mono or stereo. For mono,
either the Left or Right jack can be used and
if using stereo signals, the mono output sums
the Left and Right signals.
Note: stereo separation is maintained for
signals leaving the High Pass Output jacks.
Sub Level Control:
This sets the amount
of bass added to the system and adjusts for
the relative sensitivity of the companion full-
range speakers.
High Pass Output Jacks:
These jacks
eliminate the need for an external crossover, use
these to feed the input of your powered full-range
loudspeakers. The output signal of these XLR
jacks has the audio below 100 Hz removed.
Full Range Output Jack:
This jack
can be used to send full-range signal (mono/
summed) to additional EXM MobileSUBs or
other powered enclosures that don’t require
a stereo source.
Protection and Indicators:
This
circuitry helps prevent amplifier clipping, over
excursion and protects the amplifier and/or
voice coil from overheating.
Battery & Charging
Battery Status Indicators:
A series of
four LEDs indicate the approximate charge
level. The upper green LED is illuminated if
there’s greater than 75% charge. The red LED
indicates if the battery is critically low (approx
10% remaining) and needs immediate charging.
Note: The indicators will be engaged
only when the power switch is turned on.
Charging Indicator:
When AC is
connected, the charging indicator will
be turned on. Green indicates fully
charged, red indicates the unit is charging.
Charging:
To charge, plug into an AC power
source using the included power cord. The
charging LED indicates the charging status;
if all of the status LEDs are lit, there is still
possibly additional charging time required. The
EXM MobileSUB can be safely left connected
to AC power for charging indefinitely.
The EXM MobileSUB will not charge
when the temperature is below 0° C or
above 45° C. If it’s going to be stored
unused for a long period of time (+6
months) it is advisable to plug it in to
charge up the battery periodically. If
stored for a long period of time unused
and not been maintained, it is suggested
to connect the charger and leave it
plugged in for approximately 24 hours.
To get the full Owner’s Manual please visit our website at
http://www.yorkville.com/manuals/
or, if you need a printed version call
905-837-8777
THIS UNIT CA
N
BE OPERA
TED
WHILE CHARGING!
Printed In Canada
QuickStart-EXM-MOBILES-00-1v0 • YS#QSTART-MOBILES • April 26, 2021
EXM MobileSUB
The EXM Mobile is delivered with 40-50% of
the charge capacity. Please charge your unit for
5-hours prior to initial battery operation!