background image

16

YORK INTERNATIONAL

FORM 450.20-N20 (702)

INSTALLATION

Summary of Mounting Recommendations

Always 

mount ISN devices inside the confines

of a building or inside an enclosure suitably
rated for exposure to weather.

Never 

mount ISN devices under or beside pipes

carrying water or chemicals.

Never 

mount ISN devices near high voltage

cables, high voltage transformers or breakers, or
close to high frequency drives.

Never 

mount ISN devices in a location where

the environment could be outside the specified
operating specifications.

Never 

mount ISN devices on a vibrating surface

without first employing some form of mechani-
cal dampening.

Hardware Configuration

DIN Rail Mounting

The Universal LINC485 provides several different
options for installing within a network. The LINC is
shipped in a plastic housing with a DIN rail mounting
clip. The optional 5 VDC Power Supply also uses the
plastic housing with DIN rail mounting clip.

To attach either device, hook the lip of the clip over
the edge of the DIN rail. Press the bottom of the
device until the clip “snaps” over the lower lip of the
DIN rail.

To remove, pull the lower lip of the clip, which is
exposed below the housing, down until the lower lip
of the DIN rail is clear. Tilt the device and lift it off
the top lip of the DIN rail.

In some situations it may be desirable to remove the
Universal LINC485 from the housing and attach it to
the 5 VDC Power Supply. The housing is modular
and can be separated by using a screwdriver pressed

Figure 3. DIN Rail Mounting Options

Plastic Housing

DIN Rail

Universal LINC

Power Supply

DIN Rail

Universal LINC

Summary of Contents for Universal LINC485

































Reviews: