background image

036-21105-004 Rev. A (0902)

Unitary Products Group

3

NOTES: 

1. For condensing unit only. Does not include effect of evaporator motor power or heat.
2. Performance based on 1

5° 

superheat and 1

5° 

sub-cooling at condensing unit.

a. Increase capacity 1% for each 

2° 

increase in sub-cooling.

b. Decrease capacity 1% for each 

2° 

decrease in sub-cooling.

3. Sub-cooling in excess of 2

0° 

may result in excessively high condensing temperature with air on condenser above 115°F.

Maximum recommended condensing temperature is 140°F.

ACCESSORIES

Refer to Price Manual for specific model numbers.

Off Cycle Timer -

 Provides a 5 minute off cycle to prevent

rapid recycling of the compressor.

Room Thermostats -

 A wide selection of matching thermo-

stats is available to provide features required for any installa-
tion.

Start Assist Kit - 

Provides increased starting torque for

areas with low voltage conditions.

Compressor Blanket -

 Designed to further reduce the nor-

mal operating sounds of H3DA units.

COOLING PERFORMANCE 

MODEL

SUCT.T/P @ COMPR.

AIR TEMP ON CONDENSER

75 °F

95°F

115°F

125°F

TEMP

PSIG

MBH

KW

MBH

KW

MBH

KW

MBH

KW

H3DA012

35

61.5

13.0

1.31

10.9

1.41

9.0

1.53

8.0

1.59

40

68.5

14.5

1.36

12.3

1.49

10.2

1.62

9.1

1.69

45

76.0

16.1

1.41

13.7

1.54

11.3

1.69

10.1

1.76

50

84.0

17.7

1.44

15.2

1.58

12.4

1.74

11.1

1.82

H3DA018

35

61.5

18.7

1.83

15.6

1.99

12.5

2.09

10.9

2.13

40

68.5

20.8

1.90

17.6

2.07

14.3

2.20

12.6

2.24

45

76.0

22.9

1.97

19.6

2.17

16.2

2.31

14.5

2.37

50

84.0

25.2

2.05

21.8

2.27

18.3

2.43

16.5

2.49

H3DA024

35

61.5

21.9

2.34

18.7

2.54

15.6

2.71

14.0

2.77

40

68.5

24.3

2.41

20.9

2.63

17.6

2.84

15.9

2.91

45

76.0

26.7

2.47

23.2

2.73

19.7

2.97

18.0

3.06

50

84.0

29.3

2.53

25.6

2.82

21.9

3.10

20.0

3.20

H3DA030

35

61.5

27.6

2.64

23.9

2.88

20.2

3.11

18.3

3.20

40

68.5

30.4

2.71

26.5

2.99

22.5

3.24

20.5

3.34

45

76.0

33.3

2.78

29.2

3.08

25.0

3.37

22.8

3.48

50

84.0

36.3

2.85

31.9

3.18

27.5

3.49

25.5

3.62

H3DA036

35

61.5

33.6

3.07

28.8

3.43

24.0

3.82

21.6

4.01

40

68.5

37.3

3.09

32.1

3.48

26.9

3.88

24.3

4.08

45

76.0

40.9

3.23

35.2

3.69

30.2

4.13

27.5

4.36

50

84.0

44.8

3.37

39.1

3.85

33.3

4.35

30.4

4.60

H3DA048

35

61.5

46.7

3.87

39.1

4.82

31.9

57.8

28.3

6.39

40

68.5

51.7

4.07

43.5

5.08

35.7

6.14

31.8

6.83

45

76.0

56.8

4.28

48

5.34

39.6

6.51

35.4

7.28

50

84.0

62

4.49

52.7

5.6

43.7

6.89

39.2

7.73

H3DA060

35

61.5

53.8

5.16

48.7

6.09

43.4

7.25

40.8

7.92

40

68.5

58.9

5.33

53.1

6.25

47.5

7.41

44.7

8.08

45

76.0

64.1

5.51

57.8

6.43

51.8

7.58

48.7

8.25

50

84.0

69.6

5.71

62.5

6.61

56.1

7.76

52.9

8.43

H3DA076

35

61.5

73.9

5.55

66.2

6.60

58.3

7.98

54.4

8.82

40

68.5

80.7

5.69

72.5

6.75

64.3

8.14

60.2

8.98

45

76.0

87.7

5.84

79.1

6.91

70.5

8.30

66.2

9.15

50

84.0

95.1

5.99

86.1

7.07

76.9

8.48

72.4

9.32

SOUND RATINGS

H*DA

MODEL

SOUND RATING

DECIBELS

H3DA012

7.8

H3DA018

7.8

H3DA024

7.8

H3DA030

7.8

H3DA036

7.8

H3DA048

8.0

H3DA060

8.2

H3DA076

8.2

Summary of Contents for STELLAR 2000 H*DA012









Reviews: