manualshive.com logo in svg

York PREDATOR DM 090, Installation Instruction, Page: 7 / 44

Share
Download
York PREDATOR DM 090 Installation Instruction Download Page 7

035-17311-000 REV A (1200))

Unitary Products Group

7

INSTALLATION

PRECEDING INSTALLATION

1.

Remove the two screws holding the brackets in the front, 
rear and compressor side fork-lift slots.

2.

Turn each bracket toward the ground and the protective 
plywood covering will drop to the ground.

3.

Remove the condenser coil external protective covering 
prior to operation.

4.

Remove the toolless doorknobs and instruction packet 
prior to installation.      

 

LIMITATIONS

These units must be installed in accordance with the follow-
ing:

In U.S.A.:

1.

National Electrical Code, ANSI/NFPA No. 70 - Latest 
Edition

2.

Local building codes 

Refer to Tables 5 & 6 for unit application data.

If components are to be added to a unit to meet local codes,
they are to be installed at the dealer’s and/or customer’s
expense.

This product must be installed in strict compliance 
with the enclosed installation instructions and any 
applicable local, state and national codes includ-
ing, but not limited to, building, electrical, and 
mechanical codes.

 FIGURE 1 :  UNIT SHIPPING BRACKET

 FIGURE 2 :  CONDENSER COVERING

Bracket
Screws

Turn down

ondenser
oil Exter-

al

rotective

arometric 

elief Hood in 

hipping 

ocation (if 

 FIGURE 3 :  COMPRESSOR SECTION

Toolless
Doorknobs

Installation
Instruction
Packet

Summary of Contents for PREDATOR DM 090













































Reviews:

No comments