background image

5715184-BIM-A-0519

Johnson Controls Ducted Systems

27

VERIFY MANIFOLD GAS PRESSURE AND INPUT 

RATE

Inlet and manifold gas pressure may be measured by connecting the U
tube manometer to the gas valve with a piece of tubing. Follow the
appropriate section in the instructions below. Refer to Figure 31 for the
locations of the pressure ports on the gas valve.

Turn gas off at the ball valve or gas cock on gas supply line 
before the gas valve. Find the pressure ports on the gas 
valve marked Out P and In P.

1.

The manifold pressure must be taken at the port marked OUT P.

2.

The gas line pressure must be taken at the port marked IN P.

3.

Using a 3/32 in. (2.4 mm) hex head wrench, loosen the set screw
by turning it 1 turn counter clockwise. DO NOT REMOVE THE SET
SCREW FROM THE PRESSURE PORT.

Read the inlet gas pressure

Connect the positive side of the manometer to the IN P Tap on the gas
valve. Do not connect any tubing to the negative side of the manometer,
as it references atmospheric pressure. Refer to Figure 31 for connec-
tion details.

1.

Turn gas and electrical supplies on and follow the operating instruc-
tions to place the unit back in operation.

2.

Once the correct gas inlet pressure has been established (see
Table 15), turn the gas valve to OFF and turn the electrical supply
switch to OFF. Remove the flexible tubing from the gas valve pres-
sure tap and tighten the pressure tap plug using the 3/32 in. (2.4
mm) hex head wrench.

3.

Turn the electrical and gas supplies back on, and with the burners
in operation, check for gas leakage around the gas valve pressure
port using an approved non-corrosive gas leak detection fluid, or
other non-flammable leak detection methods.

Read the manifold gas pressure

Connect the positive side of the manometer to the OUT P Tap on the
gas valve. Do not connect any tubing to the negative side of the
manometer, as it references atmospheric pressure. Refer to Figures 31
and 32 for connection details.

Table 15: 

Inlet Gas Pressure Range

INLET GAS PRESSURE RANGE

Natural Gas

Propane (LP)

Minimum

4.5 in. W.C. (1.12 kPa)

8.0 in. W.C. (1.99 kPa)

Maximum

10.5 in. W.C. (2.61 kPa) 13.0 in. W.C. (3.24 kPa) 

IMPORTANT: 

The inlet gas pressure operating range table speci-

fies what the minimum and maximum gas line pressures must be
for the furnace to operate correctly. The gas line pressure 

MUST

BE 

a minimum of:

7 in. W.C. (1.74 kPa) for Natural Gas

11 in. W.C. (2.74 kPa) for Propane (LP) Gas

This is in order to obtain the BTU input specified on the rating plate
and/or the nominal manifold pressure specified in these instructions
and on the rating plate.

NOTICE

The regulated outlet pressure has been calibrated at the factory. 

Table 16: 

Nominal Manifold Pressure

NOMINAL MANIFOLD PRESSURE

Natural Gas

3.5 in. W.C. (0.87 kPa)

Propane (LP) Gas

10.0 in. W.C. (2.488 kPa)

 FIGURE 31:  

Gas Valve

MANIFOLD PRESSURE U TUBE CONNECTION

 FIGURE 32:  

Reading Gas Pressure

,1/(7

:5(1&+
%266

,1/(7
35(6685(
3257

21

2))

212))6:,7&+
6KRZQLQ21SRVLWLRQ

287/(7

287/(7
35(6685(
3257

9(173257

$

)/$0(
6(1625

*$69$/9(

287/(7
35(6685(7$3

*$6
%851(56

0$,1,)2/'
3,3(

´78%,1*

878%(
0$120(7(5

,1
:$7(5
&2/801
*$6
35(6685(
6+2:1

$

Summary of Contents for MM9E Series





































Reviews: