background image

5803641-JIM-B-0620

58

Johnson Controls Ducted Systems

Table 30: Cable for FC Buses and SA Buses in Order of Preference

Bus and Cable Type

Non-Plenum Applications

Plenum Applications

Part Number

O.D.

Part Number

O.D.

FC Bus: 

22 AWG Stranded, 3-Wire Twisted Shielded Cable

1

1. We strongly recommend 3-wire (for FC bus) and 4-wire, 2 twisted-pair (for SA bus), 22 AWG stranded, shielded cable. A 22 gauge cable 

offers the best performance for various baud rates, cable distances, and number of trunk devices primarily due to lower conductor-to-
conductor capacitance. Shielded cable offers better overall electrical noise immunity than non-shielded cable. Observe the shield 
grounding requirements.

Anixter:
CBL-22/3-FC-PVC
Belden®: B5501FE

0.138 in.

Anixter: CBL-22/3-FC-PLN 
Belden: B6501FE

0.140 in.

SA Bus (Terminal Block): 

22 AWG Stranded, 4-Wire, 2 Twisted-

Pair Shielded Cable

Anixter:
CBL-22/2P-SA-PVC
Belden: B5541FE

0.209 in.

Anixter: CBL-22/2P-SA-PLN
Belden: B6541FE

0.206 in.

SA Bus (Modular Jack):
26 AWG Solid 6-Wire, 3 Twisted-Pair Cable

2

2. We recommend 26 AWG solid, 6-wire (3 twisted pairs) cable as the best fit for fabricating modular cables with the modular jack housing 

assembly. Be sure the cable you use fits the modular jack housing. The preassembled cables that are available from Anixter (Part No. 
CBL-NETWORKxxx) use 24 gauge wire.

Anixter preassembled: CBL-
NETWORK25 CBL-
NETWORK50 CBL-
NETWORK75 CBL-
NETWORK100

0.15 in.

FC Bus: 

22 AWG Stranded, 3-Wire Twisted Non-Shielded Cable

Belden: B5501UE

0.135 in.

Belden: B6501UE

0.131 in.

SA Bus (Terminal Block): 

22 AWG Stranded, 4-Wire, 2 Twisted-

Pair Non-Shielded Cable

Belden: B5541UE

0.206 in.

Belden: B6541UE

0.199 in.

Table 31: Ignition Control Flash Codes

Flashes

Fault Conditions

Check

Steady On

Control Failure

Control

Heartbeat

Normal Operation

1

Not Applicable

2

Pressure Switch
 Stuck Closed

Pressure Switch

3

Pressure Switch Failed To Close

Venter Pressure Switch Vent Blocked

4

Limit Switch Open

Main Limit AUX Limit

5

Flame Present With Gas Off First Stage Gas Valve
Energized With W1 Off Second Stage Gas Valve
Energized With First Stage Gas Valve Off

Gas Valve

6

Ignition Lockout

Gas Flow Gas Pressure Gas Valve Flame Sensor

Steady Off

No Power Or Control Failure

24VAC or Control

Summary of Contents for J ZJ Series

































































Reviews: