background image

-11-

Elimination of drain

Before starting work in the morning and afternoon, elimi-

nate drain from the drain tank. Before use, purge air 

through the air hose to eliminate drain from the air hose, 

and then connect the air hose to the pneumatic tool.

Use this pneumatic tool at proper air pressure.

Using the pneumatic tool at air pressure over the specified 

air pressure could result in damage to it or accidents. To 

avoid that, be sure to mount a pressure gauge and a 

reducing valve and use the pneumatic tool at proper air 

pressure  (dynamic air pressure with the gauge of air 

piping at free speed). As the setting method of air pres-

sure,

adjust the regulator on the air piping, running the 

tool without any tip tool at free speed.

Refer to the page 20 on the specified air pressure.

Supply clean and dry compressed air.

Since dust or drain could result in malfunctions of the 

pneumatic tool or accidents, supply clean and dry com-

pressed air to it. For that purpose, it is recommended to 

install an air drier, air filter, etc.

Use proper air hose.

Use an oil-resistant air hose with abrasion-resistant exter-

nal surface and suitable for operating air pressure for the 

specified inside diameter. In addition, do not use a deterio-

rated or excessively-long air hose (recommended length: 5 

meters at maximum).

Use the proper peripheral equipment and accessories

Use the proper tip tool such as socket, bit, drill, grinding 

wheel, chisel, needles etc., for the power tool.

And when you are not sure about the usage of peripheral 

equipment and accessories (sockets, bits and couplers), 

please consult us or your dealer before using them.

Working environment:

Provide adequate lighting for the workplace and keep 

it clean at all times.

Dark or messy workplace could result in accidents. To 

avoid that, pay careful attention to lighting and make 

efforts to keep the workplace clean and tidy.

CAUTION

CAUTION

CAUTION

WARNING

WARNING

WARNING

Summary of Contents for YX-180









































Reviews: