background image

-9-

WARNING

CAUTION

Should you have any questions about the product you purchased or this 
Instruction Manual, please contact us or your YOKOTA representative.

In this Instruction Manual, safety precautions prefix either of 

the following safety alert pictograms. All are important items 

relating to safety and must be observed.

Retain this Instruction Manual in a place where it is always 

available for anyone who needs to use it.

In cases where you lose this Instruction Manual or the warning 

label affixed to the product or make it dirty, immediately 

contact us or your YOKOTA representative to obtain the 

Manual or the warning label, and then properly retain the 

Manual or replace the warning label.

In cases where you transfer or rent this product, be sure to 

attach this Instruction Manual to it.

Cases where mishandling induces a potentially 
hazardous situation which, if not avoided, could 
result in a death or serious personal injury.

Cases where mishandling induces a potentially 
hazardous situation which, if not avoided, may 
result in minor or moderate personal injury or 
property damage.

Note: Even items described in “    CAUTION” may 
lead to serious consequences depending on 
circumstances.

Warnings and cautions for safe use of pneumatic tools

Please read this manual with a full understanding of

following precautions.

Summary of Contents for YX-1100









































Reviews: