![background image](http://html.mh-extra.com/html/yokomo/bd10/bd10_manual_911814019.webp)
19
袋 #15 の内容
Bag #15 Contents
このページで使用するパーツ
Parts used on this page
20. モーターの取付け
Motor Installation
B10-302MF
モーターマウント ×1
Motor Mount
ZC-BH36
M3x6 ボタンヘッド ×4
BHS Screw
バックラッシュを合わせボタンヘッドビス (Gray)
2 本を本締めします。
Adjust the motor position so that the gears
mesh correctly and tighten the two button
head screws(Gray) to secure the motor.
2.0
ZC-BH36
M3x6 ボタンヘッド
BHS Screw
仮止程度に。
Lightly tighten.
モーター
Motor
別途ご用意下さい。
Sold separately.
ZC-SS33
M3x3 セットスクリュー
Set Screw
ピニオンギヤ
Pinion Gear
別途ご用意下さい。
Sold separately.
ZC-BH36
M3x6 ボタンヘッド
BHS Screw
B10-302MF
モーターマウント
Motor Mount
2.0
1.5
面取加工モーター推奨。
Edge trimming motor
recommendation.
平らな面
Flat side
モーターマウント / ピニオンギヤをモーターに取り付け
た後、スパーギヤの位置に合うようにピニオンギヤの位
置を合わせてセンターマウントに取り付けて下さい。
After attaching the motor mount / pinion gear to
the motor, align the pinion gear so that it
matches the position of the spur gear, and then
attach it to the center mount.
注意!
①キットにはモーター、ピニオンギヤは含まれてお
りませんので、別途ご用意下さい。
②ピニオンギヤの取り付けはモーターシャフトの
D カット されている部分にセットスクリュー
が当たる様、しっかりと締め込んで下さい。
③バックラッシュは少し隙間が出来る程度に調整し
て下さい。
(調整不足はノイズ及びギヤ破損の原因になりま
す。)
④連続走行はモーターに必要以上の負荷を掛けるだ
けでなく寿命も短くなりますので完全に冷えた事
を確認してから走行をさせて下さい。
Important!
①Motor and pinion gear not included in kit.
Please purchase separately.
②Install the pinion so that the set screw is
tightened onto the flat portion of the
motor shaft.
③Adjust the gear mesh to allow a very
small gap between the teeth of the pinion
and spur gear.
(Improper adjustment of the pinion and
spur gear may result in damage to the
gears.)
④Continuous running of the motor will
result in shorter motor life.
Allow the motor to cool between runs.
大きいピニオンギヤを使用する場合はアッパーデッキを
取り外し、モーターユニットを取り付けて下さい。
If using a large pinion gear,remove the upper deck
and attach the motor unit.
Summary of Contents for BD10
Page 1: ...1 10 SCALE EP TOURING CAR CHASSIS KIT ...
Page 29: ...MEMO ...
Page 30: ...MEMO ...
Page 31: ...MEMO ...