YOKOGAWA vigilantplant DM8 User Manual Download Page 31

Page: 31 / 63

<3. INSTALLATION, PIPING AND WIRING>

3-6

IM 12T03A01-02E

3.2

Installation of Density Converter

3.2.1

Installation Area

The density converter should be installed in the place described below;

• The vicinity of the sampling unit where maintenance or calibration is made easy. The density

converter is designed dustproof and rainproof structure so that it can be installed outdoors.

• However, when it is used with the Model VD6DF flameproof detector, it cannot be installed

the hazardous area, must be installed in the nonhazardous area. Further, when digital

output signal is used for a receiver, able length between the converter and the receiver

should be 10 m or less.

• Free from vibration.

Vibration may cause illegal contact in electric circuits.

• Avoiding from direct sunshine.
This instrument can be used in an ambient temperature of -10 to 55°C. However, direct

sunshine in summer may heat the instrument over the range.

• Free from corrosive gases and dusts.

The structure of this converter is dustproof and rainproof. However, for maintenance (with

opening front door of the converter), installation in better environment is recommended. For the

same reason, the followings are conditions for selecting installation area.

• Avoiding excessive humidity.
• Avoiding wide temperature variation.

3.2.2

Installation of Density Converter

The density converter can be installed on a panel or a wall or 2-inch pipe. The pipe should be

vertical to fix the mounting bracket on it (see Figure 3.8).

(Note): Mounting attitude is free from the converter performance. Mounting should be made of the following procedures.

Washer

Spring washer

Bolt (M8x10)

Pipe mounting

hardware

Mounting bracket

Converter

Bolt (M8x14)

Figure 3.8

Pipe Mounting

5th Edition : Dec. 11, 2015-00

Summary of Contents for vigilantplant DM8
































































Search results

Summary of Contents for vigilantplant DM8

Reviews:

Related manuals for vigilantplant DM8

Brands by name

Popular brands

YOKOGAWA vigilantplant DM8, User Manual

Search results

Summary of Contents for vigilantplant DM8

Reviews:

Related manuals for vigilantplant DM8

Brands by name

Popular brands