YOKOGAWA TA720 User Manual Download Page 94

Page: 94 / 228

7-3

IM 704510-01E

Basic Display Setup

• Overlap: Turn ON/OFF the overlapped display of the measurement results of the

pulse widths of both polarities and A-to-B time interval.

Sets whether the histograms of the measured results of positive polarity and the

histograms of the measured results of the negative polarity are displayed overlapped

(ON) or displayed separately in the top and bottom windows (OFF). The settings is

valid only in the following cases:

• A-to-B time interval measurement with the slope set to

A B

and the

calculated polarity is set to A

↑

↓

↑

or A

↑

↓

• Pulse width measurement with the polarity set to

and the calculated slope is

• Stat&Graph: Selects the display when All window is enabled.

By default, when multi window or auto window is enabled and Window is set to All,

histogram of all windows are displayed at the top section of the screen and the list of

statistical values at the bottom section. In this setting, the graph of deviation or the

graph of

can be displayed in place of the list of statistical values.

For Deviation

For

Use of Color on Histogram Displays

As shown in the table below, the color used to display the results vary depending on the

measurement function and slope/polarity. Sections where pink and light blue overlap are

displayed in violet.

Pink

Light blue

Orange

Period measurement

–

↑

↓

A-to-B time interval measurement

–

↑

↓

↑

↓

↑

↓

↑

↓

A-to-B time interval measurement

↑

↓

↑

↓

A B

Pulse width measurement

–

Pulse width measurement

Period A & period B measurement

–

↑

↓

Period A & A-to-B time interval

–

↑

↓

measurement

Pulse width A & A-to-B time interval Meas1: A

Meas1: A

measurement

Meas2:

↑

↓

↑

↓

A B

Pulse width A & pulse width B

Meas1: A

measurement

Meas2: B

7.1 Setting the Histogram Display

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands