manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

The YOKOGAWA ScopeCorder DL950 is a cutting-edge data acquisition system with powerful analysis capabilities. Enhance your experience with this versatile device by accessing the comprehensive User Manual, available for free download from manualshive.com. This manual provides detailed instructions and valuable insights for maximizing the potential of your DL950.

Share
Download
background image

10-4

IM DL950-02EN

Setting Measurement Items (Item Setup)

4.

 Tap 

Item Setup

, or press the soft key. The following screen appears.

  

Select the measurement items that you want to use.

X1:  Time value at Cursor1

X2:  Time value at Cursor2

ΔX:  Difference between the time values of Cursor1 and Cursor2

1/ΔX: Reciprocal of the difference between the time values of Cursor1 

and Cursor2

Y1:  Vertical value at the intersection of Cursor1 and the waveform

Y2:  Vertical value at the intersection of Cursor2 and the waveform

ΔY:  Difference in the vertical values at the intersection of 

Cursor1/Cursor2 and the waveform

Cursor Value Read Mode

4.

 Tap 

Other Setup

, or press the soft key.

5.

 Tap 

Cursor Read Mode

, or press the soft key to set the cursor value read mode.

The two modes available for reading Y1 and Y2 measurements are Display (display data) or 
ACQ (acquisition data).
  Display:   The screen is divided into 1001 parts, and the maximum and minimum values 

displayed on those rasters are read.

  ACQ: 

 Measurement data acquired at the sample rate of each waveform is read. When all 
traces are selected, measurement data acquired at the sample rate calculated from 
T/div and record length is read.

10.2  Measuring with Vertical Cursors

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Related manuals for ScopeCorder DL950

Landis+Gyr E450 User Manual preview
E450
Brand: Landis+Gyr Pages: 54
Eaton IQ 100 series User & Installation Manual preview
IQ 100 series
Brand: Eaton Pages: 87
Eaton Cutler-Hammer Instruction Leaflet preview
Cutler-Hammer
Brand: Eaton Pages: 16
Hardy Barth eCB1-LR Configuration Manual preview
eCB1-LR
Brand: Hardy Barth Pages: 27
UE Systems Ultraprobe 9000 Manual preview
Ultraprobe 9000
Brand: UE Systems Pages: 25
UE Systems ULTRAPROBE 10000 General Setup And Knowledge preview
ULTRAPROBE 10000
Brand: UE Systems Pages: 6
Yamaha Clavinova CVP-601 Reference Manual preview
Clavinova CVP-601
Brand: Yamaha Pages: 98
Yamaha Electone CSY-1 Manual preview
Electone CSY-1
Brand: Yamaha Pages: 28
Lake Shore Cryotronics F71 User Manual preview
F71
Brand: Lake Shore Cryotronics Pages: 97
+GF+ MSA 2 MULTI Instruction Manual preview
MSA 2 MULTI
Brand: +GF+ Pages: 64
+GF+ GF 3-2630-X Manual preview
GF 3-2630-X
Brand: +GF+ Pages: 12
+GF+ Signet 4630 Operating Instructions Manual preview
Signet 4630
Brand: +GF+ Pages: 48
Gearx P113.501 Manual preview
P113.501
Brand: Gearx Pages: 19
Rodstation PCHD02 User Manual preview
PCHD02
Brand: Rodstation Pages: 28
QEED QI-POWER-485-300 Quick Manual preview
QI-POWER-485-300
Brand: QEED Pages: 2
Leica DISTOTM D5 Quick Start preview
DISTOTM D5
Brand: Leica Pages: 2
MATO DIGIMET E30 Preset Operating Instructions Manual preview
DIGIMET E30 Preset
Brand: MATO Pages: 20
Kawai KSP 10 Owner'S Manual preview
KSP 10
Brand: Kawai Pages: 72

Brands by name

Popular brands

Load more brands