YOKOGAWA ScopeCorder DL950 User Manual Download Page 160 | Manualshive

Page: 160 / 316

background image

10-2

IM DL950-02EN

10.1 Measuring with Horizontal Cursors

This section explains the following settings for measuring T-Y waveforms with horizontal cursors:
For information on cursor measurement on X-Y waveforms, see chapter 6.3.

Items Common to Scope Mode and Recorder Mode

•  Turning the cursors on and off
•  Cursor type
•  Source waveform
•  Cursor position
•  Measurement items
•  Cursor intensity

► “Horizontal Cursors (Horizontal)” in the Features Guide

CURSOR Horizontal menu

1.

On the waveform screen’s MENU, tap

ANALYSIS

>

CURSOR

, or press

CURSOR

.

2.

Tap

Mode

, or press the soft key to select

ON

.

3.

Tap

Type

, or press the soft key to select

Horizontal

.

Set Type to Horizontal.

Set the source waveform.

Set the cursor positions.

See “Setting Measurement Items.”

Other settings

Turns cursor measurement on or off

Set the cursor display intensity.

Setting Measurement Items (Item Setup)

4.

Tap

Item Setup

, or press the soft key. The following screen appears.

Select the measurement items that you want to use.

Y1: Vertical value at Cursor1

Y2: Vertical value at Cursor2

ΔY: Difference between the vertical values of Cursor1

and Cursor2

«
...
158
159
160
161
162
...
»

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Related manuals for ScopeCorder DL950

Brand: Valeport Pages: 27

Brand: 3B6 Pages: 30

Brand: Nady Audio Pages: 2

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Hanna Instruments Pages: 9

Brand: Barksdale Pages: 2

Brand: Omega Pages: 31

Brand: YOSensi Pages: 27

Brand: Clavitech Pages: 56

Brand: kruss Pages: 115

Brand: Keller Pages: 8

Brand: SBS Pages: 17

Brand: Vaisala Pages: 11

Brand: Vanguard Instruments Pages: 85

CVM-MINI-Ethernet Series

Brand: Circutor Pages: 3

FI-500 FiberInspector Micro

Brand: Fluke Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands