background image

 

 

HART Communication

2

TI 12A01A02-60E

This document describes HART communication by the FLXA202/FLXA21 2-wire liquid 

analyzer.

 

Before communicating using the HART protocol, refer to the User’s Manual for the 

FLXA202/FLXA21 2-wire analyzer (IM 12A01A02-01E) for details of the parameters.

HART is a registered trademark of the HART Communication Foundation.

n

  What Is HART Communication?

HART Communication superimposes specific waveforms called HART Communication 

waveforms on the 4–20 mA analog signal from a FLXA202/FLXA21 to enable remote 

intercommunication between the online FLXA202/FLXA21 and a setup tool (*).

*: 

FieldMate, Plant Resource Manager (PRM), or a handheld HART communicator such as the 375 Field Communicator may be 

used as the setup tool.

Note:  When using FieldMate or a 375 Field Communicator, make sure you use the following versions or later:

FieldMate:

 

FieldMate R2.02.00 + Device Files R3.01.01

 

375 Field Communicator

System Software Version : 3.2

 

CDC Firmware Version : 1.17

 

Opereting System : 4.48

 

BIOS : 7.17

 

Koala Version : 3.9

 

CPU Board Version : 1.3

 

Baseboard Version : 2.0

n

  Downloading and installing DD files

To enable HART communication between a FLXA202/FLXA21 and setup tool, the device 

description (DD) file of the FLXA202/FLXA21 needs to be installed in the setup tool. The DD file 

contains the HART communication details and menu configurations specific to the FLXA202/

FLXA21.

FieldMate contains the latest versions of DD files at the time when sold. When using FieldMate, 

the latest DD files updated since you purchased the product can be downloaded from the 

following sites (*):

•  Yokogawa homepage: http://www.yokogawa.com/an/download/an-dl-fieldbus-001en.htm

*: 

This address is subject to change without prior notice. If the above address cannot be accessed, consult your nearest sales office 

or the agency from which you purchased the product.

l

  Before using FieldMate

Before using FieldMate, check the revision of Device Files.
• Compatibility among revisions of FLXA202/FLXA21, FieldMate and DD file

Device

HOUSING ASSY

FieldMate

DD of Field Communicator

Software 

revision 

Device 

revision

Revision of 

Device Files

DD file revision 

in Device Files

Corresponding 

device revision

DD file 

revision

FLXA21

1.20 or earlier

1

R3.01 or later

1

1

1, 2

FLXA21 

1.21 or later

2

R3.05 or 

later *

1

2

2

FLXA202/

FLXA21 

PH

2.11 or later

2

5

2

5

SC, ISC, 

DO

3

3

*: 

This revision of Device Files can be used with the FLXA202, but the device name will be displayed as FLXA21.

 

Device Files for the FLXA202 are planned to be released in December 2015.

Jun. 29, 2017-00

No. TI 12A01A02-60E 

4th Edition : Jun. 2017(YK)

All Rights Reserved. Copyright © 2013, Yokogawa Electric Corporation

Summary of Contents for FLXA202

























Reviews: