P16 OF 24
Subject to Continuous Engineering Improvement without Prior Notice.
P15 OF 24
Subject to Continuous Engineering Improvement without Prior Notice.
FUNCTIONS-REMOTE OR LINE CONTROLLER
Display Signs:
1.Once powered on, displays indoor temperature at idle status; displays set temperature during setting
temperatures in COOLING mode and HEATING mode; displays indoor temperature at other modes or
circumstances.
2.At TIMER ON or OFF, other than TIMER sign is lit, SLEEP, COOLING, or HEATING sign will be lit, if set up
TIMER ON or OFF for.
3.When unit is in operation, LED lit up once the corresponding function is clicked on: COOLING,
DUHUMIDIFICATION, FAN and HEAT.
4.Fan speed is told by the speed of the FAN sign blade spinning. At fan stopping, FAN sign blade stops spinning;
At DEFROST during HEAT mode, FAN sign blade stops spinning.
5.Error signs
FAILURE
Indoor temperature
sensor failure
Indoor coil tube
temperature sensor failure
TIMER/SLEEP LED
Lit
Lit
OPERATION LED
Blinks, 2 Times/8 Secs.
Blinks, 3 Times/8 Secs.
CENTER DISPLAY
E2
E3
Remarks:
1.Blink: lit for 0.5 sec., then off for 0.5 sec., then lit for 0.5 sec
2.E4 Code:
* Outdoor ambient temperature is too low (user remembers not to run unit during severe cold weather).
* Refrigerant at low level (users need to call service contractor to check unit).
Lit
Blinks, 4 Times/8 Secs.
E4
System runs out of
preferred design ranges
LED DISPLAY PANEL
REPARATING REMOTE OR LINE CONTROLER
Short-circuit RESET button as indicated (after the
change of the batteries).
Open the lid at back, place the 2 AAA 1.5V-LR03
batteries in right polarities.
NOTICE
If the remote controller does not operate
correctly, press RESET button to resolve it.
The signal can be transmitted as far as 275
inches (7 meters) away from the indoor unit if
the controller is pointed towards the front of
the indoor unit.
Take care of the remote/line controller. To
avoid any problem, do not drop it on the floor
or throw it or expose it at the humidity.
When press a button, the indoor unit beeps
once or twice, indicating the indoor unit has
received control signal.
Remove the batteries if you don't use the remote/line
controller for a long period.
A.Power
BATTERY ON/OFF
Once two AAA batteries are loaded into the remote controller battery compartment in the right polarity, LCD
screen shows all signs available for 3 seconds before they all go off the screen totally.
Once one or two batteries are unloaded from the remote controller battery compartment, if no button is
touched, the LCD screen display will go off in 15 seconds, if any button is pressed within 15 seconds, the LCD
screen display will go off right away.
B.Run / Stop
"ON/OFF"
If ON/OFF button is pressed the first time, LCD displays AUTO, temperature meter sign, AUTO FAN and
SWING from the top to bottom of the LCD screen;
If ON/OFF button is pressed after power off, LCD displays what is left prior to POWER OFF (including MODE,
TEMPERATURE, FAN SPEED, LOUVER, but excluding SLEEP, TIMER and FRESH).
ON/OFF
C.Temperature/Time Adjustment
These buttons are for time adjustment too. If pressed intermittently within 5 seconds after pressing TIMER ON
or TIMER OFF, time (hour) changes at 1hour/press; if held down continuously, time changes at 1hour/0.5Sec.
Time cycle is between 1-12hrs.
Temparature/Time change will show up on the Controller's LCD display.
Temperature range is 64 to 86F, Time range is 0 to 24Hr or 0 to 12Hr.
Normally, these buttons are for temperature up and down adjustment at 1F/press, to decrease 1F, press " "
button once; to increase 1F, press "
"button once; If held down for continuous adjustment, number changes at
1F/0.5Sec.
(auto)
(high)
D.Fan Speed Adjustment
FAN
(medium)
(low)
FAN MODE includes: AUTO, LOW, MED and HIGH. Every time FAN
button is pressed once, fan sign
changes once from one to the next one in a sequence: LOW (1-section/fan blade spins slowly), MED. (3-section/
fan blade spins a little quicker), HIGH (5-section/fan blade spins quicker), AUTO (4-blade fan).
E. "FRESH"
FRESH
F.
SLEEP
SLEEP
Press "SLEEP" button to turn the unit into or out of SLEEP mode. When SLEEP button is pressed, star/moon
sign either shows up or goes off. If star/moon sign is ON, MODE turns into SLEEP mode (see related function
change separately); if pressed again, star/moon sign goes off, MODE turns into the regular.
Otherwise claimed, this button is not actuated for:
* Fresh air, or,
* Manual turn on or off supplemental heating
Summary of Contents for MINI SPLIT TYPE
Page 16: ......
