YMGI LIT-WMMS-(56)-DC IVTR Installation Instructions Manual Download Page 9

INST

ALLER'S 

INSTRUCTION

P16 OF 38

INSTALL INDOOR UNIT

INSTALL THE REAR PANEL

1) Always mount the rear panel horizontally. Due to the water tray of indoor unit has been adopted the both-way 
    drainage design, the outlet of water tray should be adjusted slightly down when installing, that is taking the 
    outlet of the water tray as the center of a circle, the included angle between the evaporator and level should be 
    0 or more, that is good for condensing water drainage.

2) Fix the rear panel on the wall with screws.(Where is pre-covered with plastic granula)

3) Be sure that the rear panel has been fixed firmly enough to withstand the weight of an adult of 60kg, further 
    more, the weight should be evenly shared by each screw.

INSTALL THE PIPING HOLE

1) Make the piping hole (U55) in the wall at a slight downward slant to the outdoor 
    side.

2) Insert the piping-hole sleeve into the hole to prevent the connection piping and 
    wiring from being damaged when passing through the hole.

INSTALL THE WATER DRAINAGE PIPE

1) For well draining, the drain hose should be placed 
    at a downward slant.
2) Do not wrench or bend the drain hose or flood its 
    end by water.

3) When the long drainage hose passing through 
    indoor, should wrap the insulation materials.

Space 
to the 
wall 
5.9 inch 
above

Space 
to the 
wall 
5.9 inch 
above

2.17 
inch

CONNECT INDOOR AND OUTDOOR ELECTRIC WIRES

1) Open the surface panel.

2) Remove the wiring cover Fig 6.

3) Route the power connection cord and signal 
    control wire (for cooling and heating unit only) from 
    the back of the indoor unit and pull it toward the 
    front through the wiring hole for connection.

4) Reassemble the clampand wiring cover.

5) Recover the surface panel.

Indoor

Outdoor

Seal pad

Wall pipe

Wiring Cover

L1

L2

S

BN

BU

BK YEGN

Outdoor unit

connection

Wrenched

Bet

Flooded

Wall

Mark on the middle of it 

Gradienter

Wall

Left
0.2 inch
(Rear piping hole)

Right
0.2 inch
(Rear piping hole)

YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !

INST

ALLER'S 

INSTRUCTION

P15 OF 38

YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !

INSTALLATION DIMENSION DIAGRAM

OVER 20"

OVER 10"

OVER 10"

OVER 8"

OVER 10"

Indoor unit A

OVER 2"

OVER 4"

OVER 4"

OVER 80"

Summary of Contents for LIT-WMMS-(56)-DC IVTR






















Reviews: