YitaHome TLCFLS-1003 Assembly Instructions Manual Download Page 12

11

NOTE

CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A 

RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION, 
MOVEMENT OF A FEW CENTIMETERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEMS

TO REDUCE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURE THE MOUNTING BRACKET AND 
DOWNROD ARE SECURE

BALANCING A WOBBLING CEILING FAN

For your convenience, a balancing kit is included: please follow this procedure when balancing the fan:
1.Check that all blades and blade arm screws are secure.
2.Most fan wobbling problems result from blade levels are unequal. Check this level by selecting a point on the 
    ceiling above one fan blade’s tip. Measure this distance. Rotate the fan until the next blade is positioned for 
    measurement. Repeat for each blade. The distance deviation should be equal within 1/8" (0.32cm).
3.Use the enclosed blade balancing kit if the blade wobbling is still noticeable.
4.If the blade wobble is still noticeable, interchanging two adjacent (side by side) 
    blades can redistribute the weight and possibly result in smooth operation. 

        WARNING

: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, 

BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT OBJECTS BETWEEN ROTATING FAN BLADES

NOISE

It’s normal to hear small occasional noises when in quiet night or days. Please allow a 24-hour "breaking-in" period, 
most noises of a new fan disappear during the time.

ASSEMBLY INSTRUCTIONS

HOW TO USE BALANCING KITS

1.Periodically cleaning your ceiling fan is the only required maintenance. Use a soft brush or lint free cloth to avoid 
scratching the paint. Please turn off the electricity power before you clean your fan. 
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades or even evoke an 
electrical shock.
3.The motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF IN THE ELECTRICAL PANEL BOX BEFORE YOU DO ANY CLEANING OR REPAIRS

MAINTENANCE AND CLEANING

!

Summary of Contents for TLCFLS-1003















Reviews: