background image

SB140 

 |

  OWNER’S MANUAL

10

09

Apply grease to main pivot cavities of Rear 
Triangle.  Slide Rear Triangle Assembly onto 
main pivot and secure with Main Pivot Collet 
Axle (3.1) and Routing Collet Nut* (3.7), placing 
routing feature at the top.

Torque: 

25 Nm

 

 Install a plain collet nut (3.2, flat top with no 
clamp feature) if kit uses a wireless drivetrain.

07

Place 2x Race Extenders (3.5) onto the lower 
bearings in Link Assembly (3.16). Install into front 
triangle using Link Pivot Collet Axle (3.4) and 
plain Collet Nut (3.2).

Torque: 

25 Nm

08

Assemble Upper (3.23) and Lower (3.22) Shock Extender to SB149 Link (3.16) by placing 2X Race 
Extender (3.15) in the extender cavities and sliding between the Link tabs.  Threaded Extender (3.23) 
should be oriented to the top.  Secure with a Guide Pin and assemble Female 8x41mm Bolt (3.17) with 
Washer (3.21) through the assembly.  Secure with Male M6 Bolt (3.19) and Washer (3.20).

Torque: 

10 Nm

QC CHECK

Cycle rear triangle through to make sure motion 
is smooth.

Take precaution to make sure link does not 
contact seat tube. 

10

Place 2x Race Extenders (3.5) onto the upper bearings in Link Assembly (3.16).  Rotate Rear Triangle and 
Link together, lining up SS Pivot bores.

Install 2x SS Pivot Screws (3.3) from the inside of the Link and partially into the Rear Triangle.

Place 2x plain Collet Nut (3.2) into the Rear Triangle.

Using a wrench from the outside of the Swingarm, begin tightening in the “left-hand” direction (this is 
still a standard thread, but installed from the inside), tightening the SS Pivot Screw and Collet Nut.  

Torque: 

25 Nm

11

Install Large Collet Wedge Bolts (3.9) into  
2x Collet Axles (3.1) and (3.4)

Torque: 

14 Nm

 

Summary of Contents for SB140/LR

























Reviews: