background image

22

assemblY

Assembly

DOG & shOck mOuntinG assemblY 

 

Push the shock into the lower 

portion of the dogbone.

DOG & shOck mOuntinG assemblY

 

Use a dead blow hammer to 

install two 23.5mm reducers into the lower portion of the shock. 

threaD prep Yeti recommends prepping all threads with 
Loctite or grease. The medium strength (blue) formula along 
with proper torque is ideal for keep the bolts snug.

DOGbOne & shOck setup Press bearings flush into the bottom of 
the dogbone with shoulder facing out.  Place a spacer between the 

bearings while installing to ensure the dogbone is not bent or damaged.

Repeat for top of dogbone with shoulders of bearings facing in.  A spacer is 
not necessary for this step.

DOG & shOck mOuntinG assemblY Install the shock and dogbone 
on the frame.  Insert a 34.0 mm Ti female bolt through the drive side 

of the frame for the shock.  Use a Ti male bolt on the non-drive to tighten 
the shock into place with a 5mm allen key.  Support the bottom of the 
assembly while tightening the shock to the frame. torque:90-95 in/LB

tip: Refer to torque specifications when working with Ti assembly bolts.  
Over tightening Ti bolts may result in fractures and damage.

rear trianGle assemblY

 

Slide the swingarm over the main pivot, 

using the grooves in the swingarm to properly align over the pivot.

mOuntinG rear trianGle

  

Use the fox guide pin to align and 

hold the seatstays, dogbone, and shock together.  Use a dead blow 

hammer to push the pin through the above mentioned components.

DOGbOne anD shOck mOuntinG assemblY

 

Install the dogbone 

using a 40.5mm Ti female bolt and a Ti male bolt.  Orient the dogbone 

so the flat surface of the part is facing the rear of the frame, and use a dead 
blow hammer to insert 40.5mm female bolt through the top of the dogbone 
and the frame.  Use the Ti male bolt on the non-drive side to tighten the 
dogbone into place with a 5mm allen key. torque: 90-95 in/LB

tip:  Use the fox guide pin tool and a dead blow hammer to help guide any 
female Ti bolts through frames and frame components.

mOuntinG rear trianGle

  

Install the main pivot pin (female) from 

the drive side of the bike.  Use a dead blow hammer to push the pin 

into place. Once the female pivot pin is in place, install and tighten the male 
pivot bolt with a 5mm allen key. torque:115-125 in/LB

tip: While installing the female main pivot pin, align the swingarm with the 
main pivot bore in the front triangle with your free index finger.  Use grease 
on the threads of the male bolt and on the outside of the female pin.  This 
will help prevent binding, seizing, or stripping over time.

8

1

3

2

4

6

7

5

Summary of Contents for AS-R CARBON 2011

















Reviews: