background image

24

Assembly Cont.

assemblY

Make sure bearings on rear chainstay is flushed with metal of 
chainstay. Install seatstay with “Yeti” logo facing out above the 

dropout.

Slide a 8.5mm ID washer onto a Ti female 16.5mm and install to 
connect the seatstay and chainstay. Slide a 6.5mm ID washer onto a 

male bolt and screw into female bolt. Use 5mm key to tighten down.

tip:

 Use an elbow 5mm allen key to give more room when tightening down.

Screw male bolt into Ti female stud. Slide a 8.5mm ID washer Ti 
female stud.

13

Pull seatstay together with dogbone and shock. Use Fox guide pin to 
align everything up. Insert guide pin through junction with dead blow 

hammer.

14

mOuntinG rear trianGle

 

Slide chainstay over indentions. Grease 

up main pivot pin (58.5mm long) and align with left finger. Hammer 

into place with dead blow hammer.

Using a 6mm and 5mm allen key, use a male bolt to tighten down 
male pivot with male bolt. Once you tighten down main pivot, tighten 

down pinch bolts on chainstay with 4mm allen key.

11

12

9

10

Double-check pinch bolts on the dogbone and tighten down with 
2.5mm allen key. Double-check tightness of all other bolts.

finishinG tOuChes

 

Use dead blow hammer to hammer female stud 

through. Be ready to catch as it exits the non-drive side of the bike.  

Tighten down with 5mm allen keys.  

16

15

Summary of Contents for 4X'08-'10

















Reviews: