background image

Safety Instruction

 

  

 

 

 

 

Please conserve this manual as operation guidance. If you sell this product to other user, please 

make sure that they also receive this user manual. 

 

 

Always make sure that you are connecting to the proper voltage and that the line voltage you are 

connecting to is not higher than that stated on the decal or rear panel of the fixture. 

 

 

The fixture is intended to indoor use only. To prevent risk of fire or shock, do not expose fixture to 

rain or moisture. Make sure there are no flammable, explosive or corrosive materials surrounded 

in 0.5 meter while operating. 

 

 

The unit must be installed in a location with adequate ventilation, at least 50CM away from 

adjacent surfaces. Be sure that no ventilation slots are blocked. 

 

 

Do not operate at ambient temperatures higher than 104

(40

). 

 

 

Safe wire should be used to install machine. Bearing of safe wire should be 3 times of the 

machine weight. Complimentary signal cable transmits signals to 20 unit fixtures at most. Signal 

amplifier is a must to connect more fixtures. Sectional area of complimentary power cable is 1

In daisy chain model, it allows to connect to 4 fixtures at most. 

 

 

Always disconnect from the power source before servicing or replacing fuse/lamp and be sure to 

replace with same fuse/lamp size and type. Cut off power before moving, repairing and cleaning 

the machine.

 

 

Secure fixture using a safety chain and carrying handles. Never carry the fixture by its cord.

 

 

In case of failure or misfunction occurred, stop using the unit immediately. 

 

 

Repairs carried out by unskilled people can lead to damage or malfunction. Buy the same spare 

parts/components from manufacturer directly. 

 

 

To avoid electric shock, all fixtures must be connected to circuits with a suitable ground. Make 

sure the power cord is never crimped or damaged. Do not power on and power off the fixture in a 

short time. For your safety, do not touch fixture when running. 

 

 

When use DMX controller, please make sure that there is no interference sources(e.g. intercom, 

high frequency radio waves and radiation source)

 

Caution! 

There are no user serviceable parts inside the unit. Do not open the housing or attempt 

any repairs yourself. In the unlikely event your unit may require service, please contact your local 

distribution or after-sale service center.

 

 

本公司有权对此份产品说明书进行修改,恕不另行通知。

 

Our company reserve right to revise this user manual without notice!

 

Innovation | Efficiency | Dedication | Harmonious

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

For your safety

please read this user manual carefully before 

operation. The machine should be operated by qualified engineer

Summary of Contents for YR-IP1007H










Reviews: