background image

7

DECT Repeater RT30 User Guide

Regulatory Notices
Operating Ambient Temperatures

• Operating temperature: +32 to 104°F (0 to 40°C)

•Relative humidity: 5% to 90%, noncondensing

•Storage temperature: -22 to +160°F (-30 to +70°C)

Warranty

Our product warranty is limited only to the unit itself, when used normally in 

accordance with the operating instructions and the system environment. We are 

not liable for damage or loss resulting from the use of this product, or for any claim 

from a third party. We are not liable for problems with Yealink device arising from 

the use of this product; we are not liable for financial damages, lost profits, claims 

from third parties, etc., arising from the use of this product.

Explanation of the symbols

• DC  symbol

        

 is the DC voltage symbol.

•WEEE Warning symbol

To avoid the potential effects on the environment and human health as a result 

of the presence of hazardous substances in electrical and electronic equipment, 

end users of electrical and electronic equipment should understand the 

meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as 

unsorted municipal waste and have to collect such WEEE separately. 

 

              

• Restriction of Hazardous Substances Directive (RoHS)

This device complies with the requirements of the EU RoHS Directive. Statements of 

compliance can be obtained by contacting [email protected].

•Safety Instructions

Save these instructions. Read these safety instructions before use!

 General Requirements

• Before you install and use the device, read the safety instructions carefully and 

observe the situation during operation.

• During the process of storage, transportation, and operation, please always keep 

the device dry and clean,avoid collision and crash.

•Please attempt not to dismantle the device by yourself. In case of any 

discrepancy, please contact the appointed maintenance center for repair.

•Please refer to the relevant laws and statutes while using the device. Legal rights 

of others should be respected as well.

 Environmental Requirements

•Place the device at a well-ventilated place. Do not expose the device under 

direct sunlight.

•Keep the device dry and free of dusts.

•Do not place the device on or near any inflammable or fire-vulnerable object, 

such as rubber-made materials.

•Keep the device away from any heat source or bare fire, such as a candle or an 

electric heater.

 Operating Requirements

•Do not let a child operate the device without guidance.

•Do not let a child play with the device or any accessory in case of accidental 

swallowing.

•Please use the accessories provided or authorized by the manufacturer only.

Summary of Contents for MSpeaker II













Reviews: