manualshive.com logo in svg

Yealink MeetingEye 400, Administrator'S Manual, Page: 11 / 278

Share
Download
Yealink MeetingEye 400 Administrator'S Manual Download Page 11

 | About This Guide | 

11

• Yealink CPW90-BT Bluetooth Wireless Microphones Quick Start Guide, which describes how to use

CPW90-BT.

• Yealink Wi-Fi USB Dongle WF50 User Guide, which describes how to connect the wireless network to

the VCS codec and provide wireless AP via WF50.

• Yealink WPP20 Wireless Presentation Pod User Guide, which describes how to use WPP20 wireless

presentation pod.

• Yealink PSTN Box CPN10 Quick Start Guide, which describes how to connect VCS codec to PSTN.
• Yealink VCC22 Video Conferencing Camera Quick Start Guide, which describes how to connect the

VCC22 video conferencing cameras to the VCS codec.

• Yealink CTP20 Quick Start Guide, which describes how to connect CTP20 to the VCS codec.
• Yealink VCM34 Quick Start Guide, which describes how to connect VCM34 to the VCS codec.
• Yealink VCH51 Quick Start Guide, which describes how to connect VCH51 to the VCS codec.
• Yealink Soundbar Quick Start Guide, which describes how to connect Soundbar to the VCS codec.
• Yealink MSpeaker II Quick Start Guide, which describes how to connect MSpeaker II to the VCS codec.

You can download these documentations online:

http://support.yealink.com/documentFront/forwardToDocumentFrontDisplayPage

.

For support or service, please contact your Yealink reseller or go to Yealink Technical Support online:

http://support.yealink.com/

.

Summary of Changes

•

Changes for Release 43, Guide Version 43.33

•

Changes for Release 30, Guide Version 43.30

•

Changes for Release 43, Guide Version 43.10

•

Changes for Release 42, Guide Version 42

Changes for Release 43, Guide Version 43.33

This guide is also available to MeetingEye 600 video conferencing system which is newly issued.

The following sections are new for this version:

•

Hardware of MeetingEye 600

•

Setting the Default Layout for Dual Single Screen

Changes for Release 30, Guide Version 43.30

This guide is also available to MeetingEye 400 video conferencing system which is newly issued.

The following sections are new for this version:

•

Hardware of MeetingEye 400

•

Hardware of VCR20 Remote Control

•

Specifying the Camera Control Mode for MeetingEye 600/MeetingEye 400

•

Enabling People Counting

Changes for Release 43, Guide Version 43.10

The following sections are new for this version:

•

Enabling/Disabling the PC Port

•

Setting Screen Saver for VP59

•

Setting Wallpaper for VP59

Summary of Contents for MeetingEye 400























































































































































































































































































Reviews:

No comments