manualshive.com logo in svg

Yealink MeetingEye 400, Administrator'S Manual, Page: 161 / 278

Share
Download
Yealink MeetingEye 400 Administrator'S Manual Download Page 161

 | Configuring Video Settings | 

161

Parameter

Description

Configuration Method

While Content
Sharing

 (it is

only applicable to
MeetingEye 600/
MeetingEye 400)

Configure the default layout of a single
screen when a call is established and
has content sharing.

•

1+N—

the selected video image is

displayed in the large window and
other video images are displayed in
small windows.

•

Selected Speaker

—the selected

video image is displayed in full
screen.

•

Equal NxN

—the remote and the local

video images are displayed in the
same size.

Default

: 1+N.

Web user interface

Setting the Default Layout for Dual Single Screen

When you connect two monitors to the system, you can configure the default layout for each monitor when
a call is established. This feature is only applicable to MeetingEye 600.

Procedure

1.

On your web user interface, go to 

Setting

 > 

Display

 > 

Remote Session (In A Call)

 > 

Dual Display

.

2.

Configure and save the following settings:

Parameter

Description

Configuration Method

HDMI 1

Configure the default video layout for
HDMI 1 when a call is established.

•

1+N

—the remote video image is

displayed in the large window and the
local video image is displayed in a
small window at the screen bottom.

•

Selected Speaker

—the remote or the

local video image is displayed in full
screen.

•

Equal NxN

—the remote and the local

video images are displayed in the
same size.

•

Picture in Picture

—the remote video

image is displayed in a large window,
and the local video image is reduced
to a thumbnail in the bottom-right
corner of the large window.

Note

: when no participant shares

content, the remote video image
is displayed in full screen; when a
participant shares content, the video
layout is displayed in the PiP (Picture-in-
Picture) mode by default.

Web user interface

Summary of Contents for MeetingEye 400























































































































































































































































































Reviews:

No comments