Ybravo BRAVO 21- 201 BBC Operator'S Manual Download Page 9

9

ASSEMBLY - SETUP 

Taking the following precautions will lessen the 
risk of injury and property damage.
Use extreme care in handling gasoline. Gasoline is 
extremely fl ammable and the vapors are explosive.

- Extinguish all cigarettes, cigars, pipes, and other 
  sources of ignition.
- Use only approved gasoline containers.
- Never remove gas cap or add fuel with the engine 
  running.  
- Allow engine to cool a minimum of 3 minutes 
  before refueling.
- Never fuel the machine indoors.  
- Never store the machine or fuel container where
  there is an open fl ame, spark, or pilot light such
  as on a water heater or other appliances.
- Never fi ll containers inside a vehicle or on a truck
  or trailer bed with a plastic liner.  Always place 
  containers on the ground away from your vehicle
  when fi lling.
- Remove the mower from the truck or trailer and
  refuel it on the ground.  If this is not possible,
  then refuel the equipment with a portable container,
  rather than from a gasoline dispenser nozzle.
- Keep the nozzle in contact with the rim of the fuel
  tank or container opening at all times until fueling
  is complete.  Do not use a nozzle lock-open device.
- If fuel is spilled on clothing, change clothing 
  immediately.
- Never overfi ll fuel tank.  Always wipe off any
  spilled fuel or oil.  Replace fuel cap and tighten.

WARNING

MAXIMUM

FUEL LEVEL

FUEL FILLER

NECK

FUEL FILLER CAP

APPROVED FUEL
CONTAINER

STEP 8  Honda Engine 

Verify that the throttle control is adjusted properly as follows:

Move the throttle control to the Full Throttle position.

In the full throttle position the two arms at the throttle 

mechanism on the engine should touch as illustrated below.

Choke 

Full Throttle

Idle Throttle

Engine Off

OK

Following these steps for the throttle adjustment will ensure 
that the Honda engine performs properly for this mower. 
The engine speed was adjusted at the factory to be 
approximately 3100 to 3200 RPM. 

NOTICE:

The engine speed should preferably be checked and verifi ed 
with a tachometer.  Normal full throttle speed of the engine 
should be adjusted to 3100 to 3200 RPM.  An authorized 
Honda or Kawasaki Engine Dealer can verify and adjust the 
engine speed properly. 

STEP 8 Kawasaki Engine

Verify that the throttle control is adjusted properly as follows:

Move the throttle control to the Choke position.

- In the Choke position the arm attached to the throttle cable at 
the engine should bottom out at the arrow. 

Following these steps for the throttle adjustment will ensure 
that the Kawasaki engine performs properly for this mower. 
The engine speed was adjusted at the factory to be 
approximately 3200 RPM.

Choke 

Full Throttle

Idle Throttle

Engine Off
(BBC version)

STEP 9

Before fi lling the engine with gasoline - follow all instructions 
in this manual as well as all instructions provided in the Honda  
or Kawasaki engine Owner’s Manual.   
Maximum fi ll volume: 
Honda:        1.5 Qt (1.4 Liter)  - 86 octane or higher
Kawasaki:   1.9 Qt (1.8 Liter) -  86 octane or higher

The engine will not operate on gasoline marketed as 
E-85 (85% ethanol)

Summary of Contents for BRAVO 21- 201 BBC
















Reviews: