background image

English

-

8

SAFETY

These instructions are for your safety. Read them carefully.

IMPORTANT: 

THIS CUTTING MACHINE IS 

CAPABLE OF AMPUTATING HANDS AND FEET AND 
THROWING OBJECTS. FAILURE TO OBSERVE 
THE FOLLOWING SAFETY INSTRUCTIONS COULD 
RESULT IN SERIOUS INJURY OR DEATH.

General Operation

• 

Read, understand, and follow all instructions 
on the machine and in the manual before 
starting.

• 

Do not put hands or feet near rotating parts 
or under the machine. Keep clear of the 
discharge opening at all times.

• 

Only allow responsible adults, who are 
familiar with the instructions, to operate the 
machine.

• 

Clear the area of objects such as rocks, toys, 
wire, etc., which could be picked up and 
thrown by the blades.

• 

Be sure the area is clear of bystanders 
before operating. Stop machine if anyone 
enters the area.

• 

Never carry passengers. The machine is only 
intended for use by one person.

• 

Do not mow in reverse unless absolutely 
necessary. Always look down and behind 
before and while backing.

• 

Never direct discharged material toward 
anyone. Avoid discharging material against 
a wall or obstruction. Material may ricochet 
back toward the operator. Stop the blades 
when crossing gravel surfaces.

• 

Do not operate machine without the entire 
grass catcher, discharge guard, or other 
safety devices in place and working

• 

Slow down before turning.

• 

Never leave a running machine unattended. 
Always turn off blades, set parking brake, 
stop engine, and remove keys before 
dismounting.

WARNING!

This symbol means that important safety instructions need to be emphasized. 
It concerns your safety.

8011-512

Read the operator’s manual before starting the machine

Clear the area of objects before mowing

8011-513

Summary of Contents for ZMMKW34170





































































Reviews: