background image

TROUBLESHOOTING

English

-

49

The engine overheats.

Battery not charging.

• 

Poor contact with battery terminal cable 
connectors.

• 

Charging lead is disconnected.

The machine moves slowly, unevenly, or not at all.

• 

Parking brake on.

• 

Bypass valve on pump open.

• 

Drive belt for the transmission slack or 
has come off.

• 

Air trapped in hydraulic system.

Mower deck not engaging.

• 

Drive belt for the mower deck has come loose.

• 

Contact for the electromagnetic coupling has 
loosened.

• 

The blade switch is faulty or has come loose, 
from the cable contact.

• 

The fuse has blown.

Transaxle leaks oil.

• 

Damaged seals, housing, or gaskets.

• 

Air trapped in hydraulic system.

• 

Clogged air intake or cooling fi ns.

• Engine 

overloaded.

• 

Poor ventilation around engine.

• 

Defective engine speed regulator.

• 

Too little or no oil in the engine.

• 

Fouled spark plugs.

Uneven mowing results.

• 

Different air pressure in the tires on the left and 
right sides.

• Bent 

blades.

• 

The suspending for the mower deck is uneven.

• 

The blades are dull.

• 

Driving speed too high.

• 

The grass is too long.

• 

Grass collected under the mower deck.

Problem

Cause

Summary of Contents for ZMMKW34170





































































Reviews: