background image

English-

14

SAFETY INSTRUCTIONS

run over or into anything. If necessary, 
make repairs before starting.

Never make adjustments with the engine 
running.

The machine is tested and approved only 
with the equipment originally provided or 
recommended by the manufacturer. Only 
use approved repair parts for the 
machine.

The blades are sharp and can cause 
cuts and gashes. Wrap the blades or use 
protective gloves when handling them.

Check the parking brake’s functionality 
regularly. Adjust and service as 
necessary.

The mulch blades should only be used in 
familiar areas when higher quality 
mowing is desired.

Reduce the risk of fire after using the 
machine by removing grass, leaves, and 
other debris that may have accumulated 
on the machine. Allow the machine to 
cool before putting it in storage.

Clean deck and underside of deck after 
each use, and avoid spraying engine and 
electrical components with water.

Transport

The machine is heavy and can cause 
serious crushing injuries. Be extra 
cautious when it is loaded on or 
unloaded from a vehicle or trailer.

Use an approved trailer to transport the 
machine. Activate the parking brake, turn 
off the fuel supply, and fasten the 
machine with approved fastening 
devices, such as bands, chains, or 
straps, when transporting. 

Do not operate this machine on public 
roadways.

Check and abide by local traffic 
regulations before transporting the 
machine on any road.

Do not tow this machine, it may cause 
damage to the drive system.

Do not tow any trailers, etc. with this 
mower. They may jackknife or overturn 
causing damage to the mower and 
possibly serious injury to the operator.

8011-644

Clean the machine regularly

IMPORTANT INFORMATION
The parking brake is not sufficient to lock 
the machine in place during transport. 
Ensure that the machine is well fastened 
to the transport vehicle. Always reverse 
the machine onto the transport vehicle to 
avoid tipping it over.

Summary of Contents for ZEKW48190





















































































Reviews: