Yazoo/Kees ZEKH42200 Page 28 Operator'S Manual Download | Manualshive

Page: 28 / 80

background image

English-

26

OPERATION

4.

Disengage the mower blades by
depressing the blade switch.

5.

Move the steering controls outward to
the locked (outer) neutral position.

6.

Move the throttle to the middle position.

8011-668

Depress the control for disengaging the mower deck

8011-724

Steering controls in the outward, locked neutral position

8011-763

Set the throttle

«
...
26
27
28
29
30
...
»

Summary of Contents for ZEKH42200

















































































Reviews:

No comments

Related manuals for ZEKH42200

Brand: Jacobsen Pages: 20

Brand: Meec tools Pages: 30

Brand: Stihl Pages: 120

Brand: Tar River Pages: 56

Brand: Tanaka Pages: 57

eclipse 2 InCommand

Brand: Jacobsen Pages: 86

Brand: Garland Pages: 172

Brand: Etesia Pages: 42

Brand: Stiga Pages: 30

Brand: Snapper Pages: 28

Brand: MTD Pages: 44

Brand: Flymo Pages: 10

Brand: Snapper Pages: 1

Brand: Troy-Bilt Pages: 48

Brand: Snapper Pages: 16

Brand: Racing Pages: 20

Brand: Troy-Bilt Pages: 40

Brand: Kubota Pages: 299

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands